1 / 35

Heat Exchangers Design and Construction

Heat Exchangers Design and Construction. Chemicoz. Introduction:. Shell and tube heat exchangers are one of the most common equipment found in all plants. How it works?. What are they used for?. Classification according to service . . Heat Exchanger.

reya
Download Presentation

Heat Exchangers Design and Construction

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Heat Exchangers Design and Construction Chemicoz

  2. Introduction: • Shell and tube heat exchangers are one of the most common equipment found in all plants • How it works?

  3. What are they used for? • Classification according to service . • Heat Exchanger Both sides single phase and process stream • Cooler One stream process fluid and the other cooling water or air • Heater One stream process fluid and heating utility as steam • Condenser One stream condensing vapor and the other cooling water or air • Reboiler One stream bottom stream from a distillation column and the other a hot utility or process stream

  4. Design codes: • Code Is recommended method of doing something ASME BPV – TEMA • Standard is the degree of excellence required • API 660-ASME B16.5–ASME B36.10M–ASME B36.19-ASME B16.9–ASME B16.11 • Specifications • Is a detailed description of construction, materials,… etc • Contractor or Owner specifications

  5. Main Components 1- Channel Cover 8- Shell 2- Channel 9- Baffles 3- Channel Flange 10- Floating Head backing Device 4- Pass Partition 11- Floating Tubesheet 5- Stationary Tubesheet 12- Floating Head 6- Shell Flange 13- Floating Head Flange 7- Tube 14 –Shell Cover

  6. TEMAHeat Exchanger

  7. TEMA Heat Exchanger • Front Head Type A - Type B - Type C - Type

  8. TEMA Heat Exchanger • Shell Type E - Type F - Type J - Type K - Type

  9. TEMA Heat Exchanger • Rear End Head Types M - Type S - Type T - Type Fixed Tubesheet Floating Head Pull-Through Floating Head

  10. Classification: • U-Tube Heat Exchanger • Fixed Tubesheet Heat Exchanger • Floating Tubesheet Heat exchanger

  11. Example AES

  12. Example AKT

  13. Heat Exchangers Mechanical Design • Terminology • Design data • Material selection • Codes overview • Sample calculations • Hydrostatic test • Sample drawing

  14. Terminology • ASME • TEMA • API • MAWP • MDMT • PWHT • NPS – DN – NB – NPT • Sch - BWG

  15. Design Data • Heat Exchanger Data Sheet : • TEMA type • Design pressure • Design temperature • Dimensions / passes • Tubes ( dimensions, pattern) • Nozzles & Connections • Baffles (No. & Type)

  16. Material Selection

  17. Strength • A – Yield Strength B A C • B – Tensile Strength • C – Rupture point

  18. Strength • Creep Strength a slow plastic strain increased by time and temperature (time and temperature dependant) for stressed materials • Fatigue Strength The term “fatigue” refers to the situation where a specimen breaks under a load that it has previously withstood for a length of time • Toughness The materials capacity to absorb energy, which, is dependant upon strength as well as ductility

  19. ASME code Overview Sec.I Power Boilers Sec.II Materials Sec.III Nuclear Fuel Containers ASME BPV code Sec.IV Heating Boilers Sec. V Non Destructive Examination Sec. VI Operation of heating boilers Sec. VII Operation of power boilers Sec. VIII Pressure vessels Sec. IX Welding and Brazing Sec. X Fiber-Reinforced plastic PV Sec. XI Inspection of nuclear power plant Sec. XII Transport tanks

  20. ASME code overview • Sec. II: Materials • Part A : Ferrous material specifications • Part B : Non-Ferrous material specifications • Part C : Specifications of welding rods, electrodes and filler metals • Part D : Properties • Sec. VIII: Rules of construction of pressure vessels • Division 1 : 3 Subsections + mandatory Annex + non mandatory Annex • Division 2: Alternative rules • Division 3 : Alternative rules of high pressure

  21. ASME code overview

  22. TEMA code overview • TEMA classes: • Class R: Generally severe requirements for petroleum and related processing applications • Class C: Generally moderate requirements of commercial and general processing applications • Class B: Chemical Process service • TEMA subsections • 10 subsection

  23. Sample Calculations • Shell thickness calculations under Internal Pressure: PR . t = + CA + UT SE – 0.6 P • t : Min. Required Shell Thickness • P : Design Pressure of Shell Side • S: Max. Allowable Stress of Shell Material • R: Shell Inside Radius (corroded conditions) • E : Joint Efficiency • CA: Corrosion Allowance • UT: Under Tolerance (if applicable)

  24. Sample Calculations • Channel thickness calculations under Internal Pressure: PR . t = + CA + UT SE – 0.6 P • t : Min. Required Channel Thickness • P : Design Pressure of Tube Side • S: Max. Allowable Stress of Channel Material • R: Channel Inside Radius (corroded conditions) • E : Joint Efficiency • CA: Corrosion Allowance • UT: Under Tolerance (if applicable)

  25. Sample Calculations • Body Flanges:

  26. Sample Calculations • Body Flanges: • Trial and error calculations • Gasket seating conditions • Operating conditions • No. of bolts and size • Bolt circle diameter • Inside and outside diameters • Check min. and max. bolt spacing • Detailed analysis of the flange • Forces calculations • Moment calculations • Stresses calculations

  27. Sample Calculations • Precautions in body flanges design and installations: • Pairs of flanges • Bolt holes shall straddle center line • Corrosion Allowance • Cladding • Bolts shall be multiple of 4 • Bolting shall be allowed to be removed from either side • Calculated thickness not include the RF

  28. Sample Calculations • Nozzles and standard flanges: • Flange Rating (ASME B16.5) • Area replacement calculations • Nozzle neck thickness calculations • Impingement protection Sample

  29. Sample Calculations • Tubesheet: • Tubesheet is the principal barrier between shell side and tube side • Made from around flat piece of metal with holes drilled for the tubes • Tubes shall be uniformly distributed • Tubesheet thickness shall be designed for both sides • Tubesheet shall be designed for bending stresses and shear stresses • Corrosion allowance

  30. Sample Calculations • Tubesheet: • Tubesheet thickness for bending T: Effective tubesheet thickness S: Allowable stress P: Design pressure corrected for vacuum if applicable at the other side η: Ligament efficiency For Square pattern For Triangular pattern G: Gasket effective diameter F: Factor

  31. Sample Calculations • Tubesheet: • Tubesheet thickness for Shear: T: Effective tubesheet thickness DL: Effective diameter of the tube center parameter DL=4A/C C: Perimeter of the tube layout A: Total area enclosed by the Perimeter C P: Design pressure S: Allowable stress do: Outside tube diameter

  32. Tube-to-Tubesheet joint • Expanded • Strength welded • Seal welded

  33. Hydrostatic Test • Test pressure : 1.3 X MAWP • Test Procedure • Gasket change

  34. Sample drawing • Construction drawing is the design output Sample drawing 1 Sample drawing 2

  35. Thank You Chemicoz chemicozz@gmail.com

More Related