1 / 47

Basic Electronics

Basic Electronics. I. OHM'S LAW. R. V. V = I * R. volts = amps * ohms volts = mA * Kohms. resistor. I. 1/R. V. I = V/R = 9V/1K = 9mA = .009A. I. LED. anode. ~10 mA. I. cathode. + 1.5 V -. I = ??. ARDUINO CONTROL OF LED. ARDUINO. 5V. 0V. PIN 0. 20 mA max. GND.

riva
Download Presentation

Basic Electronics

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Basic Electronics

  2. I OHM'S LAW R V V = I * R volts = amps * ohms volts = mA * Kohms

  3. resistor I 1/R V I = V/R = 9V/1K = 9mA = .009A I

  4. LED anode ~10 mA I cathode + 1.5 V - I = ??

  5. ARDUINO CONTROL OF LED ARDUINO 5V 0V PIN 0 20 mA max GND digitalWrite(0,HIGH); delay(1000); digitalWrite(0,LOW);

  6. ARDUINO 5V, 20 mA DEVICE PIN 0 GND What if device needs more than 5V or more than 20 mA??

  7. Computer controlled switch V big DEVICE I big STAMP PIN 0 GND

  8. Transistor current-controlled amplifier, current-controlled switch BASE COLLECTOR I small I big = b*I small EMITTER Think: spray can!

  9. COLLECTOR BASE EMITTER Ic = b*Ib Ib Ie = Ib + Ic ONE-WAY!

  10. 5V 0V ON ON I I OFF OFF V V Vce sat 0.1 – 2.0 V LOAD: MOTOR, SOLENOID, RELAY, LAMP, …

  11. Things to look for on a data sheet • Max current, Ic max • Max volts, Vce max • Max power, P max • Vce sat • Gain, Hfe or b • Switching time

  12. 2N3904

  13. TIP 120

  14. Interfacing to Motors

  15. Motor interface FOR SMALL MOTOR, USE 2N3904

  16. Pin 2 Pin 2 GND GND - - + +

  17. Arduino pin limits 20 mA per PIN 40 mA TOTAL 10.6 mA 4.4 mA 1 A

  18. Hook motor straight to Arduino?

  19. POWER

  20. + V - P = V * I I P = ?? I = V/R = 9/10 = 0.9 A P = V*I = 9*.9 = 8.1 W

  21. demo

  22. HEAT I, V t, w I P = 12 * I

  23. WOW! WHAT A GREAT MOTOR I GOT AT AX-MAN! AND IT RUNS ON 12v!

  24. 12V Later… YOUCH!! IT'S HOT!

  25. 5 V Ic Ib Vce sat ~ 2.0 V Let Ic = 5 A PWR = V*I = 2.0*5 = 10 W !!! HOT wasted

  26. RELAYS To control larger loads

  27. Relays • Electromagnet-controlled switch • User for (1) larger loads, (2) bi-directional motor COIL CONTACTS COIL  control side 12V, 120 ohm, 100 mA 5V, 500 ohm, 10 mA CONTACTS  load side 240 VAC/28 VDC, 10 A 100 VDC, 1A 120 VAC/24 VDC, 0.5 A/1.0A

  28. Types of relays GENERAL PURPOSE COIL: 12, 24 VDC; 120 VAC CONTACTS: 5-10 A REED COIL: 5, 12 VDC CONTACTS: .5-2 A SOLID STATE COIL: LOGIC INPUT CONTACTS: 2-25 A

  29. JAMECO 174431

  30. COIL: 12 V, 400 OHM, I = V/R = 12/400 = 30 mA CONTACT: 24 VDC, 15 A

  31. Transistor drive for a relay NOTE: RELAY COIL CAN SUCK CURRENT

  32. SOLENOIDS For linear, short-range, on-off motion

  33. x Force when energized F x ¼ in. MAX ON-TIME = ½ SEC

  34. www.jameco.com

  35. SPST SPDT Switches (NO, NC)

  36. #define MOTOR 0 #define SWITCH 4 . . . digitalWrite(MOTOR,HIGH); delay(1000); // wait for motor to clear switch while (digitalRead(SWITCH) ; digitalWrite(MOTOR,HIGH);. . .

  37. SMALL WIRE + HIGH CURRENT WIRE 1. CONNECT POINTS OF EQUAL VOLTAGE 2. CARRY CURRENT STRANDED SOLID Flexible Higher current Type Gauge Max I Notes Wrap wire 30 200 mA wrapping, signal level only Hookup 24/22 1-2 A general purpose Lamp cord 18 5 A House wire 14/12 15/20 A “CABLE” = multiconductor wire bundle e.g. modular phone cord: 28g solid, 4 conductor

  38. Primary Zinc Alkaline (most common) Lithium (camera, watch) Secondary (rechargeable) Sealed lead acid (car) Gel NiCd NiMH Lithium Important specs Energy density Voltage Zinc/Alkaline: 1.5 V Lead Acid: 2.0 V cars: 6, 12 V NiCd: 1.2 V Power tools: 4.8, 6.0, 7.2, 9.6, 12, 18 V Maximum current “Cold-cranking amps” Capacity Amp-hours or mAHrs BATTERIES

  39. 12 V (10 cell) NiCd pack rated at 1300 mAH 1.3 Amps for 1 hour 520 mA for 2.5 hours…..in theory Top-notch cells for RC racing can provide 2300 mAH 9V alkaline 580 mAH @ 12 mA (can deliver 12 mA for 48 hrs) 100 Service life Hrs 1 10 100 mA Alkaline technology 9V Discharge curve t Capacity and discharge See www.duracell.com (or other sites) for more

  40. Battery technologies

  41. www.hardingenergy.com

More Related