1 / 12

MCS specification

MCS specification. An MCS is accepted if: | dX|  0.1 mm AND | dY|  0.1 mm AND | dT |  3 mrad. An MCS is rejected if: | dX| > 0.3 mm OR | dY| > 0.3 mm OR | dT | > 3 mrad. An MCS with either | dX| or | dY| greater than 0.1 mm is still accepted if:

sileas
Download Presentation

MCS specification

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. MCS specification M. Allitt, MEB December 2003 • An MCS is accepted if: • |dX|  0.1 mm AND • |dY|  0.1 mm AND • |dT|  3 mrad. • An MCS is rejected if: • |dX| > 0.3 mm OR • |dY| > 0.3 mm OR • |dT| > 3 mrad. • An MCS with either |dX|or|dY| greater than 0.1 mm is still accepted if: • |dX|  0.3 mm, |dY|  0.3 mm and |dT|  3 mrad AND • The mean and standard deviation of |dX| and |dY| calculated using a sample set numbering at least 50 magnets are both  0.1 mm;

  2. MCDO specification (1) • An MCD module is accepted if: • |dX|  0.1 mm AND • |dY|  0.1 mm AND • |dT|  4 mrad. • An MCD module is rejected if: • |dX| > 0.3 mm OR • |dY| > 0.3 mm OR • |dT| > 4 mrad. • Should either |dX| or|dY| be greater than 0.1 mm, any MCD module will still be acceptable provided that: • |dX|  0.3 mm, |dY|  0.3 mm and |dT|  4 mrad; • The mean and standard deviation of |dX| and |dY| calculated using a sample set numbering at least 50 MCD are both  0.1 mm; M. Allitt, MEB December 2003

  3. MCDO specification (2) • An MCO module is accepted if: • |dX|  0.3 mm AND • |dY|  0.3 mm AND • |dT|  4 mrad. • An MCO module is rejected if: • |dX| > 0.3 mm OR • |dY| > 0.3 mm OR • |dT| > 4 mrad. M. Allitt, MEB December 2003

  4. Conclusions • MCS • More than half of the total MCS needed have been produced. • Average dX, dY close to zero, standard deviation ~ 0.05 mm • Average dT ~ 0.2 mrad, standard deviation ~ 1 mrad • Distribution of European MCS slightly narrower than distribution of Indian MCS, but will probably end up the same • MCDO • Insufficient data for European MCDO • Unknown and not constant co-ordinate system for Indian measurements mean we can’t check the distribution of all magnets. • For Indian MCDO checked at CERN, average dX, dY close to zero, standard deviation ~ 0.05 mm • Average dT ~ - 0.2 to -0.3 mrad, standard deviation ~ 1 mrad M. Allitt, MEB December 2003

  5. Table VI: MQT tuning quadrupole.

More Related