1 / 28

KX-NS1000 Step by Step Guide Network Survivability

KX-NS1000 Step by Step Guide Network Survivability. March 6, 2014. Panasonic System Networks PBX SE team. Specifications are subject to change without notice. Trunk Adaptor. Trunk Adaptor. 1. Introduction.

stepheng
Download Presentation

KX-NS1000 Step by Step Guide Network Survivability

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. KX-NS1000 Step by Step GuideNetwork Survivability March 6, 2014 Panasonic System NetworksPBX SE team Specifications are subject to change without notice.

  2. Trunk Adaptor Trunk Adaptor 1. Introduction Back-up is available automatically for SIP trunk incl E1 / PRIadapter, KX-NT/UT IP-phone and one look connection. PRI/E1 or SIP Provider Back-up master PBX works as slave PBX usually.But it works as master PBX after master PBX stops working. KX-NS1000 (2nd)Back-up Master SIP Trunk One-Look AK One-Look AK KX-NS1000 (1st)Master KX-UT KX-UT KX-NT KX-NT PRI/E1 or SIP Provider After master PBX stops working, KX-NS1000Back-up Master SIP Trunk One-Look AK One-Look AK KX-NS1000Master KX-UT KX-NT KX-UT KX-NT

  3. 2. Table of Contents

  4. Chapter 1Specifications

  5. Trunk Adaptor Trunk Adaptor 11. Back-up of SIP trunk and KX-NT/UT AlternativeSolution forW-CPUW-Power Supply Back-up is available automatically for SIP trunk inclE1 / PRI adapter and KX-NT/UT IP-phone. IP address of 1st PBX (Master) and 2nd PBX (Back-up) can be assigned to NT.1st PBX informs IP address of 2nd PBX to UT during working. IP address of SIP server is pre-programmed to 2nd PBX also for back-up during working. PRI/E1 Adapter or SIP Provider SIP Trunk One-Look AK One-Look AK KX-NS1000 (1st)Master KX-NS1000 (2nd)Back-up Master KX-UT KX-NT PRI/E1 or SIP Provider After master PBX stops working, KX-NS1000Back-up Master SIP Trunk One-Look AK One-Look AK If 2nd PBX cannot communicate with 1st PBX, 2nd PBX starts working for SIP provider. If NT/UT cannot communicate with 1st PBX, NT/UT starts working with 2nd PBX. KX-NS1000Master KX-UT KX-NT

  6. 12. Back-up of One-look Back-up is available for One-look network also. One-Look AK One-Look AK KX-NS1000Slave One-Look AK One-Look AK KX-NS1000Master KX-NS1000Back-up Master Back-up is available for Activation Key automatically.It works for 10 days as temporal AK after master PBX stops working. Temporal AK One-Look AK One-Look AK Other AK All AK of 1st PBX is informed to 2nd PBX during working. KX-NS1000Master KX-NS1000Back-up Master

  7. 13. Back-up of Analog CO and AK Back-up is available for Analog CO by parallel cabling. Telephone Company KX-NS1000Master KX-NS1000Back-up Master

  8. 14. Conditions for Back-up Conditions- Left message in Built-in VM for Master PBX cannot be transferred to Back-up PBX. It is recommended to use VM to E-mail feature always.- IP address of Master PBX and Back-up PBX is not same. So CTI application cannot work automatically.- Max. one Back-up Master can be assigned.- Because one IP phone is registered as two extensions for back-up,Max. 500 IP phones can work with Back-up feature. (Not all 1000) Max. 128 SIP trunk (incl E1/PRI adapter) for Back-up (Not all 256) One-Look AK One-Look AK 301 201 202 302 101 102 KX-NS1000 (2nd)Back-up Master KX-NS1000 (1st)Master EXT 201in 2nd PBX EXT 102 in 1st PBXEXT 302 in 2nd PBX EXT 202in 2nd PBX EXT 101 in 1st PBXEXT 301 in 2nd PBX Ext 3xx in 2nd PBX works as Ext 1xx after master PBX stops working.Walking extension feature works automatically.

  9. 15. Isolated Mode Slave PBX can work independently in following case.- Both Maser PBX and Back-up Master PBX stop working or communication with both stops working .- Back-up Master PBX was not prepared and Master PBX stop working or communication with Master PBX stops working . IP CH AKin Slave PBX IP CH AKin Slave PBX IP CH AKin Master PBX IP CH AKin Master PBX Master Slave Master Slave Conditions- AK for IP ch in Master PBX is not transferred to slave PBX.- AK for other such as Cellular Link feature is transferred to slave PBX. It works for 10 days as temporal AK after master PBX stops working. - If extension in slave PBX uses VM mail box in master PBX, VM cannot work. VM in same PBX should be used.

  10. 16. Return to Normal mode Back-up Master mode or Isolated mode does not finish automatically after communication with master PBX works again.Manual operation is required to Master PBX. This specification does not allow unexpected return before complete trouble shooting of network.

  11. 17. Other conditions - System data is copied to slave PBX (Back-up Master / Isolated). System data is data which can be programmed by web maintenance console such as speed dial, ARS and so on. - Data in SRAM is not copied to slave PBX (Back-up / Isolated). SMDR / Charge / Error Log / Timed Reminder / Extension Dial Lock / Check-In Check-Out / Clean Up status/ Login Logout / Ready Not Ready- When communication between master PBX does not work for 40 seconds (programmable), slave PBX restarts automatically, and Back-up Master mode or Isolated mode starts.- When back-up Master mode or Isolated modes starts, error log can be sent from slave PBX by e-mail.

  12. Chapter 2Programming forBack-up Master

  13. 21. Programming Programming for Master Back-up master mode can be assigned whenslave unit is added in “Add Site Wizard”. KX-NS1000Other Slave KX-NS1000Master KX-NS1000Back-up Master (Slave)

  14. 22. Programming Programming for Master Back-up master mode can be changedto other slave PBX. KX-NS1000Other Slave KX-NS1000Master KX-NS1000Back-up Master (Slave) Note: New back-up master unit will be restarted automatically.

  15. 23. Programming Programming for Master Timer can be adjusted. KX-NS1000Other Slave KX-NS1000Master KX-NS1000Back-up Master (Slave) 40s : Slave was communicating with Master. But after no communication for 40s,Slave PBX decides independence and reboot automatically. After reboot (3min), it works independently. 40s can change to 30s.300s : Slave was working with Master and power-off. When Salve cannot communicate withMaster for 300s after power-on again, Slave PBX starts working independently.

  16. Chapter 3Programming for Back-up ofSIP Trunk incl E1/PRI adapter

  17. Trunk Adaptor 31. Programming Programming for Slave PRI/E1 Adapter orSIP server SIP server registration has to bepre-programmed to slave unit also.“Back-up mode” has to be programmedto work this only when communicationbetween master PBX is disabled. KX-NS1000Other Slave TRG 1for example KX-NS1000Master KX-NS1000Back-up Master (Slave)

  18. Chapter 4Programming for Back-up ofKX-NT / KX-UT Phone

  19. 41. Programming Programming for Slave Make extension for “Secondary”.This is dummy extension. Dummy extension number such as 301should be unused number for realextension now and in future.Virtual IP Extension card for KX-NTVirtual UT Extension card KX-UT KX-NS1000Other Slave KX-NS1000Master KX-NS1000Back-up Master (Slave) EXT 101 in 1st PBXEXT 301 in 2nd PBX

  20. 42. Programming Programming for Master Assign the secondary extension to 1st extension. KX-NS1000Other Slave 301302303 : 101102103 : KX-NS1000Master KX-NS1000Back-up Master (Slave) EXT 101 in 1st PBXEXT 301 in 2nd PBX

  21. 43. Programming Programming for Master Assign 2ndary extension to 1st extension. KX-NS1000Other Slave 301302303 : 101102103 : KX-NS1000Master KX-NS1000Back-up Master (Slave) EXT 101 in 1st PBXEXT 301 in 2nd PBX

  22. 44. Confirmation Result can be confirmed as follows.

  23. 45. Programming Programming for Phone KX-NS1000Other Slave KX-NS1000Master KX-NS1000Back-up Master (Slave) EXT 101 in 1st PBXEXT 301 in 2nd PBX Secondary PBX IP address has to be assigned to KX-NT phone manually. Secondary PBX IP address is informed to KX-UT from master PBX automatically.KX-UT software has to be latest.

  24. 46. Conditions Technically any back-up combination is available.But Master to Back-up Master is recommended because AK for IP channels is transferred from Master to Back-up Master only. Real EXT 105 in Other Slave PBXDummy EXT 305 in Master PBX KX-NS1000Other Slave Real EXT 106 in Other Slave PBXDummy EXT 306 inBack-up Master PBX KX-NS1000Master KX-NS1000Back-up Master (Slave) Recommend Real EXT 101 in Master PBXDummy EXT 301 in Back-up Master PBX Real EXT 103 in Back-up Master PBXDummy EXT 303 in Other Slave PBX Real EXT 102 in Master PBXDummy EXT 302 in Other Slave PBX Real EXT 104 in Back-up Master PBXDummy EXT 304 in Master PBX

  25. Chapter 5Programming forIsolated mode

  26. 51. Programming Programming for Slave Isolated mode has to be enabled.(Default is disable.) KX-NS1000Other Slave KX-NS1000Master KX-NS1000Back-up Master (Slave)

  27. Thank you !

  28. Revision

More Related