1 / 9

ECET 340 Devry Course Tutorial - ecet340dotcom

For more course tutorials visit<br>www.ecet340.com<br><br>ECET 340 Week 1 HomeWork 1<br>ECET 340 Week 1 iLab 1<br>ECET 340 Week 2 HomeWork 2<br>ECET 340 Week 2 iLab 2<br>ECET 340 Week 3 HomeWork 3<br>ECET 340 Week 3 iLab 3<br>ECET 340 Week 4 HomeWork 4<br>ECET 340 Week 4 iLab 4<br>

student04
Download Presentation

ECET 340 Devry Course Tutorial - ecet340dotcom

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ECET 340 ASH COURSE TUTORIAL-ecet340dotcom

  2. ECET 340 ASH Course Tutorial ECET 340 Entire Course (All ilabs and Homework) (Devry) ECET 340 Week 1 HomeWork 1 (Devry) Given “the requirements of each signal’s destination must match the capabilities of the signal’s source,” name some of the electrical signal parameters that must be considered when designing an interface between two different hardware components. (2 points) • ECET 340 Week 1 HomeWork 1 • ECET 340 Week 1 iLab 1 • ECET 340 Week 2 HomeWork 2 • ECET 340 Week 2 iLab 2 • ECET 340 Week 3 HomeWork 3 • ECET 340 Week 3 iLab 3 • ECET 340 Week 4 HomeWork 4 • ECET 340 Week 4 iLab4ECET 340 Week 5 HomeWork 5 • ECET 340 Week 5 iLab 5 • ECET 340 Week 6 HomeWork6

  3. ECET 340 ASH Course Tutorial ECET 340 Week 1 iLab 1 (Devry) ECET 340 Week 2 HomeWork 2 (Devry) Where does program control transfer to when an interrupt occurs? +2 points 2. Which one of the following Interrupts has highest priority? +2 points 3. RAM Vector table addresses $3E52 belongs to which interrupt? +2 points 4. Before exiting an ISR, the programmer should use which command? +2 points 5. In which one of the following sequences is the stack pulled by rti? +3 points • To become familiar with Microcontroller MC9S12 parallel ports and how simple input and output devices are interfaced through them. • To learn how to program I/O instructions in C language. • To learn how to organize a program to read data from input ports, process the data, and display the result on a simple output device.

  4. ECET 340 ASH Course Tutorial ECET 340 Week 2 iLab 2 (Devry) ECET 340 Week 3 HomeWork 3 (Devry) . In Figure 7.32 on page 339 of the Huang textbook, if the row has and the columnsare , which key is pressed? (2 points max) 3. In Figure 7.32 on page 339 of the Huang textbook, explain why the 10kΩ resistors ties to VCC are required. (2 points max) • ECET 340 Week 2 iLab 2

  5. ECET 340 ASH Course Tutorial ECET 340 Week 3 iLab 3 (Devry) ECET 340 Week 4 HomeWork 4 (Devry) . If an 8-bit SAR has Vref = 10 V, what is the binary value for an input voltage of 7.28 V?3. What is the percent error for the binary answer found in Problem #2?4. Given an 24 MHz bus speed. Write down the line(s) of instruction which set the ATD1 unit for 2MHz conversion frequency, 10-bit resolution and 8 A-to-D clocks per sample time. • To learn the basic operation of a keypad. • To understand how to interface a keypad to a microprocessor. • To learn how to program a keypad driver in C language. • To learn how to program a keypad activated interrupt that identifies the key being pressed and displays or otherwise returns its value to the main program.

  6. ECET 340 ASH Course Tutorial ECET 340 Week 4 iLab 4 (Devry) ECET 340 Week 5 HomeWork 5 (Devry) Given Iref = 2 mA for a DAC1408 IC, find Iout for the input 1110 11103. Find the number of discrete voltages output by a 12-bit DAC. Show work.4. Use the internet to locate the data sheet for an MC1408 DAC. From it find, for the MC1408-7 version, the following: a. The settling time • To learn how to use A-to-D converters to digitize signals from analog input devices. • To learn how to write a C language program that samples the data from an analog device, digitizes it and formats it for output on an LCD. • To become more proficient in programming displays for real-time operation.

  7. ECET 340 ASH Course Tutorial ECET 340 Week 5 iLab 5 (Devry) ECET 340 Week 6 HomeWork 6 (Devry) What are the four main functions of the HC12 Timer unit?2. Two input capture events occur at counts 0x1037 and 0xFF20 of the free-running counter. How many counts (in decimal) have transpired between these two events? • This week's lab covers two areas, conversion of digital HCS12signals to an analog format, and the use of a Serial Peripheral Interface (SPI)to transfer data, and commands between the HCS12, and the DACperipheral.

  8. ECET 340 ASH Course Tutorial ECET 340 Week 6 iLab 6 (Devry) ECET 340 Week 7 HomeWork 7 (Devry) The movable part of the solenoid is the: +2 points 2. Why is the 6N139 optoisolator used in the interfaces to devices such as large motors? +2 points 3. Calculate the number of steps per revolution for a stepper motor with a step angle of 7.5°. +2 points • ECET 340 Week 6 iLab 6

  9. ECET 340 ASH Course Tutorial To make excellent academic records.., Keep following our site!!! To make excellent academic records.., Keep following our site!!!

More Related