ECET 340 DEVRY Course Tutorial/Uoptutorial

1. ECET 340 DEVRY Tutorial Course For More Course Tutorials Visit www.uoptutorial.com

2. ECET 340 DEVRY Tutorial Course ECET 340 Entire Course ECET 340 Week 1 HomeWork 1 • ECET 340 Week 1 HomeWork 1 • ECET 340 Week 1 iLab 1 • ECET 340 Week 2 HomeWork 2 • ECET 340 Week 2 iLab 2 • ECET 340 Week 3 HomeWork 3 • ECET 340 Week 3 iLab3 • ECET 340 Week 4 HomeWork 4 • ECET 340 Week 4 iLab 4 • ECET 340 Week 5 HomeWork 5 • ECET 340 Week 5 iLab 5 • 1. Give three examples each of internal and external peripheral devices as referenced to the HCS12 microcontroller and not an entire PC. (2 points)2. Given “the requirements of each signal’s destination must match the capabilities of the signal’s source,” name some of the electrical signal parameters that must be considered when designing an interface between two different hardware components. (2 points)

3. ECET 340 DEVRY Tutorial Course ECET 340 Week 1 iLab 1 ECET 340 Week 2 HomeWork 2 • OBJECTIVES: • To become familiar with Microcontroller MC9S12 parallel ports and how simple input and output devices are interfaced through them. • To learn how to program I/O instructions in C language. • To learn how to organize a program to read data from input ports, process the data, and display the result on a simple output device. • 1. Where does program control transfer to when an interrupt occurs? +2 points • 2. Which one of the following Interrupts has highest priority? +2 points • 3. RAM Vector table addresses $3E52 belongs to which interrupt? +2 points • 4. Before exiting an ISR, the programmer should use which command? +2 points • 5. In which one of the following sequences is the stack pulled by rti? +3 points

4. ECET 340 DEVRY Tutorial Course ECET 340 Week 2 iLab 2 ECET 340 Week 3 iLab3 • ECET 340 Week 2 iLab 2 • SOLVED ECET 340 iLAB3 • OBJECTIVES: • To learn the basic operation of a keypad. • To understand how to interface a keypad to a microprocessor. • To learn how to program a keypad driver in C language. • To learn how to program a keypad activated interrupt that identifies the key being pressed and displays or otherwise returns its value to the main program.

5. ECET 340 DEVRY Tutorial Course ECET 340 Week 3 HomeWork 3 ECET 340 Week 4 HomeWork4 • 1. Sketch a circuit that can be used to debounce a pushbutton and explain how it works. (4 points max) • 2. In Figure 7.32 on page 339 of the Huang textbook, if the row has and the columnsare , which key is pressed? (2 points max) • 3. In Figure 7.32 on page 339 of the Huang textbook, explain why the 10kΩ resistors ties to VCC are required. (2 points max) • 1. Determine the conversion time for an ADC0804 (8-bit), where 66 clocks per bit are required, if its clock frequency is 50 kHz.2. If an 8-bit SAR has Vref = 10 V, what is the binary value for an input voltage of 7.28 V?3. What is the percent error for the binary answer found in Problem #2?4. Given an 24 MHz bus speed. Write down the line(s) of instruction which set the ATD1 unit

6. ECET 340 DEVRY Tutorial Course ECET 340 Week 4 iLab 4 ECET 340 Week 5 HomeWork 5 • I. OBJECTIVES: • To learn how to use A-to-D converters to digitize signals from analog input devices. • To learn how to write a C language program that samples the data from an analog device, digitizes it and formats it for output on an LCD. • To become more proficient in programming displays for real-time operation. • 1. Explain, briefly, why an analog restoring filter is sometimes used at the output of a DAC. 2. Given Iref = 2 mA for a DAC1408 IC, find Iout for the input 1110 11103. Find the number of discrete voltages output by a 12-bit DAC. Show work.4. Use the internet to locate the data sheet for an MC1408 DAC. From it find, for the MC1408-7 version, the following: • a. The settling time

7. ECET 340 DEVRY Tutorial Course ECET 340 Week 5 iLab 5 ECET 340 Week 6 HomeWork 6 • Scenario/SummaryThis week’s lab covers two areas, conversion of digital HCS12signals to an analog format, and the use of a Serial Peripheral Interface (SPI)to transfer data, and commands between the HCS12, and the DACperipheral.DeliverablesFor this lab, the deliverables include the cover sheet,filled-in sections of the lab report, photographs (online), or instructor • 1. What are the four main functions of the HC12 Timer unit? 2. Two input capture events occur at counts 0x1037 and 0xFF20 of the free-running counter. How many counts (in decimal) have transpired between these two events?3. What is the maximum time possible before the free-running counter overflows when the e MHz?

8. ECET 340 DEVRY Tutorial Course ECET 340 Week 6 iLab 6 ECET 340 Week 7 HomeWork 7 • ECET 340 Week 6 iLab 6 • 1. The movable part of the solenoid is the: +2 points • 2. Why is the 6N139 optoisolator used in the interfaces to devices such as large motors? +2 points • 3. Calculate the number of steps per revolution for a stepper motor with a step angle of 7.5°. +2 points • 4. How is stepper motor speed controlled? State any two ways a program can do this. +2 points

9. ECET 340 DEVRY Tutorial Course ECET 340 Week 7 iLab 7 • ECET 340 Week 7 iLab 7

10. ECET 340 DEVRY Tutorial Course For More Course Tutorials Visit www.uoptutorial.com