1 / 22

Workbench - Simulation Basics

Workshop 2. Workbench - Simulation Basics. Notes on Workshop 2. The first workshop is extensively documented. As this course progresses, students will become more familiar with basic Workbench Simulation functionality (menu locations etc.), thus subsequent workshops will contain less details.

swanl
Download Presentation

Workbench - Simulation Basics

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Workshop 2 Workbench - Simulation Basics

  2. Notes on Workshop 2 • The first workshop is extensively documented. As this course progresses, students will become more familiar with basic Workbench Simulation functionality (menu locations etc.), thus subsequent workshops will contain less details. • Throughout these workshops menu paths are documented as: “First pick > Second pick > etc.”. • Workshops begin with a goals section followed by an assumptions section. March 29, 2005 Inventory #002216 WS2-2

  3. Workshop 2 - Goals • Using the Stress Wizard, set up and solve a structural model for stress, deflection and safety factor. • Problem statement: • The model consists of a Parasolid file representing a control box cover (see figure). The cover is intended to be used in an external pressure application (1 Mpa/145 psi). • The cover is to be made from aluminum alloy. • Our goal is to verify that the part will function in its intended environment. March 29, 2005 Inventory #002216 WS2-3

  4. Workshop 2 - Assumptions • We will represent the constrains on the counter bores, bottom contact area and inner sides using frictionless supports. • Frictionless supports place a normal constraint on an entire surface. Translational displacement is allowed in all directions except into and out of the supported plane. Since we would expect frictional forces to at contact areas this is a conservative approach. March 29, 2005 Inventory #002216 WS2-4

  5. Workshop 2 - Start Page • From the launcher start Simulation. • Choose “Geometry > From File . . . “ and browse to the file “Cap_fillets.x_t”. • When Workbench - Simulation starts choose “Stress Branch – Ductile Material” under “Structural Simulation”. March 29, 2005 Inventory #002216 WS2-5

  6. Workshop 2 - Environment • Loads: the load consists of a 1 MPa pressure applied to the 17 exterior surfaces of the cover. March 29, 2005 Inventory #002216 WS2-6

  7. . . . Workshop 2 - Environment • Supports: As described earlier frictionless supports are applied on 3 different regions of the model. • Note: the use of all frictionless surfaces will trigger the message shown here: • Workbench Simulation automatically places weak springs on structural models where the potential of rigid body motion exists. An inspection of the boundary conditions on this model should confirm that rigid body motion is prevented. In this case the weak springs have no effect on the results. • This is an informational warning that the model should be inspected. It does NOT indicate the solution is invalid. • The weak spring feature can be configured on/off by the user. March 29, 2005 Inventory #002216 WS2-7

  8. Workshop 2 - Preprocessing Setup working unit system: • From the main menu go to “Units > Metric (mm, Kg, MPa, °C, s). March 29, 2005 Inventory #002216 WS2-8

  9. . . . Workshop 2 - Preprocessing • From the Simulation Wizard choose “Verify Material”. Locate the “Material” detail field and choose to “Import…” > “Aluminum Alloy”. • Notice that verifying and changing material automatically highlighted the part branch in the tree. March 29, 2005 Inventory #002216 WS2-9

  10. . . . Workshop 2 - Preprocessing Loads: Select the 17 exterior surfaces of the cover. To simplify selection • Select 1 surface (choice is arbitrary). • Click “Extend to Limits” to select the remaining 16 surfaces. 4 3 March 29, 2005 Inventory #002216 WS2-10

  11. 6 7 . . . Workshop 2 - Preprocessing Loads Continued: • Choose “Insert Loads” from the SimWiz. • Structural > Pressure. • Enter a Magnitude of 1 Mpa in the Details window. 5 March 29, 2005 Inventory #002216 WS2-11

  12. . . . Workshop 2 - Preprocessing Supports (counter bores): • Select the 4 counter bore surfaces (figure below shows 1). • Choose “Insert Supports” from the SimWiz. • Structural > Frictionless Support 10 8 9 March 29, 2005 Inventory #002216 WS2-12

  13. . . . Workshop 2 - Preprocessing Supports (inner sides): • Select one of the inside surfaces of the bottom recess. Click the “Extend to Limits” button to add the remaining 7 surfaces to the selection set (8 total). • Choose “Insert Supports” from the SimWiz. • Structural > Frictionless Support 11 13 12 March 29, 2005 Inventory #002216 WS2-13

  14. . . . Workshop 2 - Preprocessing Supports (bottom): • Select the surface at the bottom of the recess. • Choose “Insert Supports” from the SimWiz. • Structural > Frictionless Support 14 16 15 March 29, 2005 Inventory #002216 WS2-14

  15. Workshop 2 - Solution • From the SimWiz choose “Solve”. The callout will direct you to the solve icon at the top of the GUI. Alternately you could right click on any branch in the tree and choose “solve”. 17 March 29, 2005 Inventory #002216 WS2-15

  16. Workshop 2 - Results • From the SimWiz choose “View Results”. The call out will direct you to the Solution branch. Selecting various results branches will cause that result to be plotted (see next page). 18 March 29, 2005 Inventory #002216 WS2-16

  17. . . . Workshop 2 - Results • Plotting a model’s deformation often provides a “reality check” in structural analysis. Verifying the general nature (direction and amount) of deflection can help avoid obvious mistakes in model setup. Animations are often used as well. March 29, 2005 Inventory #002216 WS2-17

  18. . . . Workshop 2 - Results • After reviewing stress results expand the safety tools and plot safety factors and margins. Notice both failure theories predict a minimum safety factor of < 1. March 29, 2005 Inventory #002216 WS2-18

  19. Workshop 2 - Report • To create an html report first click the “Report Preview” tab. The customization page allows you to set up the report. • At this point simply choose “Generate Report” to review the default setup. March 29, 2005 Inventory #002216 WS2-19

  20. . . . Workshop 2 - Report • When the report generation is complete scroll through the report and review its contents. • Notice at this point there are no graphic images. Return to the “Geometry” tab to insert figures. March 29, 2005 Inventory #002216 WS2-20

  21. . . . Workshop 2 - Report • Choose the graphical items you wish to include in your report by first highlighting the branch and orienting the plot. • Next right click and insert a figure. • The next time the report is generated the figures will be included. March 29, 2005 Inventory #002216 WS2-21

  22. . . . Workshop 2 - Report Notes on Figures: • Figures are not limited to results items. Adding a plot of the environment branch, for example, will include an image of model boundary conditions in the Report. • Figures are independent. You may set up individual figures and have their orientation, zoom level, etc. retained regardless of the active model orientation or other figures. • Individual branches can have multiple figures associated with them. March 29, 2005 Inventory #002216 WS2-22

More Related