1 / 21

PC Maintenance –Cs 006

PC Maintenance –Cs 006. Simple Troubleshooting on PC. Troubleshooting guide for the Motherboard. Motherboard is the main part of computer. Any error or problem may result in whole system failure.

tanisha-wood
Download Presentation

PC Maintenance –Cs 006

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. PC Maintenance –Cs 006 Simple Troubleshooting on PC

  2. Troubleshooting guide for the Motherboard • Motherboard is the main part of computer. • Any error or problem may result in whole system failure. • Before you do any thing else, you must remove enough of the case cover so that you can see the CPU and the BIOS ROM. • Then, get out your penlight and your notebook and pen or pencil. As you move through the next few steps, write down every bit of information you identify.

  3. Essential steps • Identify the processor’s class model. For example, is it an Intel 8088, 286/16, Intel Pentium III 600, Slot 1, AMD Athlon, or another processor. • Identify BIOS manufacturer and its version level. For example, Phoenix BIOS I4HS10 rev 4.05.10. This information can be obtained during the boot sequence, if you are fast, or from a label on the BIOS chipset or on the BIOS manufacturer’s Web.

  4. Cont… • Identify motherboard manufacturer and model – Near the edge of the motherboard, you will find a block of printed information that identifies the manufacturer, the model number, and possibly a revision level. • Identify the bus type- Which expansion buses are supported on the motherboard or any riser boards in use PX, ISA, MCA,EISA, VLB, PCI etc.

  5. Identifying the problem • There are three general failures directly related to the motherboard. These are best characterized by a POST (power-on self test) beep code and the action immediately following it. These three categories are beep, boot and bam. • To begin the identification process, power on the PC, listen and look and then go to the section below that most appropriates what you heard and saw.

  6. No Beep, No Boot • The PC power is on, you can see lights on the front panel, but as near as you can tell the POST process did not run. 1. Check both ends of the main power cord, especially where it connects to the back of the PC, to make sure that it is fully pushed into the connector or receptacle. Inspect the power cord for corrosion, damage or loose connection.

  7. Cont… 2. Check the power source outlet or proper voltage with a multimeter or (Digital voltage meter). If may be easier just to try plugging the PC into a different outlet. If the PC plugged into a power strip, its varistor may have been blown out by an electrical surge. Some plug strips have a fuse or circuit breaker that can be reset.

  8. Cont… 3. Check the power supply fan to see if is turning. If it is turning, the problem may be in the power supply, and you need to troubleshoot it. 4. If power supply fan is spinning, but nothing else is happening, the power to the motherboard may be faulty. For example, you may have a +12V source, but no +5V or +3.3V supplies. It may also be that the power good line from power supply is not coming on for some reason.

  9. Cont… 5.Verfy that the power connectors from power supply are firmly seated and in the correct position. Check to make sure the power supply connector on the motherboard is firmly seated. 6. If the PC is in a public area, such as a laboratory, student lab, library, or another open and unsecured location, there could be a missing processor, or expansion card. Unfortunately, theft is common on PCs to which there is public access.

  10. Cont… 7. Look for smoke and smell for burnt wire. • You may want to use a small magnifying glass to examine the motherboard and its components for heat damage. 8. Try reseating all the expansion cards, memory modules, and if the PC older, the ROM BIOS chip. You may want to check on any socket – mounted chips on the motherboard.

  11. Cont… 9. Remove the motherboard from the case and place it on an antistatic surface or material. Reconnect the motherboard to its power and device connectors and attempt to boot . If it works, something in the case or a part of the mounting of the board is causing it to short while it is in the case.

  12. Beep, No Boot • If the PC powers on, but the POST process appears to halt after sounding one or more beeps, then follow this troubleshooting procedure. • Make sure the PC’s monitor is on and operating properly. • Look up the pattern used on the BIOS in your PC.

  13. Cont… • Each BIOS manufacturer uses a different and unique pattern of beep tones to signal errors. Once you know what you are listening for, attempt to write down the pattern of the beep tones. Remember that tones are short or long with varying length pauses inserted between beep series.

  14. Cont… • You may need to reboot several times before you are sure, consult your motherboard’s documentation or visit the BIOS manufacturer’s Web for its meaning and a suggested procedure to correct the problem. 3. Check to make sure that the CMOS battery jumper is in the correct position.

  15. Cont… • Inspect the CMOS battery for leak, corrosion or burns. You should also check the battery with multimeter. It could just be time for a new battery. 4. If the beep codes are for something very generic, check the video card by removing and installing it. If it does not work, try swapping it out for another video card of the same type, if available.

  16. Cont… • Depending on when the error detected by the POST , you may get some text message or a part of the BIOS information. If so, study the information displayed; it ca usually provide clues to where the problem is occurring. 5. Remove the RAM chips or modules and try to boot with different combination of memory modules in different slot on the board.

  17. Cont… • Verify that the RAM chips or modules in use are compatible with the motherboard, chipset and processor. Also be sure that modules are installed in the proper sets., and try to reboot. 6. Reset the expansion cards. 7. Remove all of the expansion boards, except the video adapter. If the system reboot, the problem is likely one of the boards or the expansion bus on one of the expansion slots.

  18. Cont… • Disconnect the system speaker. It could be shorting to the board.

  19. Beep, Boot, Bam • In this situation, the PC is powered on, the POST completes and singles an all clear but the PC fails at the beginning or the boot sequence or right after the boot complete. 1. Study the BIOS information displayed on the monitor and verify that the boot drive sequence is set correctly.

  20. Cont… 2. Check the hard disk drives to ensure that you have only one Master disk and one Slave on each IDE cable. Check the boot sequence. If boot still fails, change the boot sequence and attempt to boot off an alternative media(CD/DVD, etc)

  21. Cont... 3. Try replacing the controller card of the boot disk and reboot. 4. Review your motherboard manufacture’s Web site for further detailed explanation on compatibility.

More Related