1 / 40

CIE 338 - Soil Mechanics and Foundations II

CIE 338 - Soil Mechanics and Foundations II. Soil Properties and Site Investigation Shallow Foundation Design Deep Foundation Design Retaining Structures and Slope Stability. Building Codes. Local and national codes guide practice. Design must conform to code or

tarak
Download Presentation

CIE 338 - Soil Mechanics and Foundations II

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. CIE 338 - Soil Mechanics and Foundations II • Soil Properties and Site Investigation • Shallow Foundation Design • Deep Foundation Design • Retaining Structures and Slope Stability

  2. Building Codes Local and national codes guide practice. Design must conform to code or Departures require approval Compliance does not assure safety or economy

  3. P Column Ground Surface Df Footing B Shallow Foundation Df < 4B

  4. A = total building foundation plan area Af = Individual footing area If  Af => 0.5 A then consider a mat foundation

  5. Column Loads Df Mat B Shallow (Mat) Foundation Df < 4B

  6. Deep Foundation- Piles Friction Pile End Bearing Pile Hammer Hammer Hard Soil / Rock Firm Soil

  7. Pile Shaft Hammer Poured in place fill Pre bored hole Deep Foundations

  8. Foundation Df < 4B Df > 4B Shallow Deep Af < 0.5A Af > 0.5A Driven Cast in Place Footing Pile Shaft Mat Caisson Pier Bored Pile Af =sum of footing areas Df = depth of cover A = plan area of structure B = footing width

  9. Earth Retaining Systems Wall System (external) Stabilized Earth System (internal)

  10. Slope Stability How steep can the slope be? What is the factor of safety (FS)? How can we improve the FS?

  11. Foundations transfer loads to subsurface DL - dead loads consist of the structure load usually well known LL - live loads are service loads, wind, earthquake usually involve large uncertainty

  12. Types of Loads • Normal Loads, P • Shear Loads, V • Moment Loads, M • Torsion Loads, T (usually negligible)

  13. z y

  14. Normal load important for buildings P z y

  15. Shear load important for retaining walls z Vy, Vx y Vy

  16. Moment load important for retaining walls and buildings z Mx Mx, My y

  17. Torsion load usually not significant z T y

  18. Applied loads induce: Failure - (collapse/instability) Design with a generous factor of safety Movement - (settlement/deformation) Design to a performance criteria

  19. Factor of Safety (FS) against failure or for bearing capacity FS = Resistance/Driving FS for buildings ~ 3 FS for retaining structures and slopes ~1.5

  20. Movement / Settlement / Deformation Uniform settlement - least critical Even tilting - can be critical Distortion - potentially troublesome

  21. Uniform settlement, 

  22. Even tilting,  (limit < 1/250)

  23. s s As built foundation   D 

  24.  = maximum total settlement D= maximum differential settlement S = column spacing  = distortion = D/ S Da = a * S a, denotes allowable

  25. a = allowable rotation (Table 2.2, Coduto) Type of structurea Frame warehouse 1/200 Steel and reinforced concrete buildings 1/600 Unreinforced masonry 1/2500

  26. Consult Fig. 2.9 and 2.10 (Coduto) Upper limit of D/  for foundations on sand = 1 Upper limit of D/  for foundations on clay ~ 0.3 The allowable total settlement is set to limit D

  27. Example 2.1 A steel frame building without diagonal bracing S = 20 ft on clay foundation, what are the allowable total and differential settlements? Da = a * S obtain a = 1/500 (Table 2.2) Da = 0.5 in obtain D/ = 0.8 (Fig 2.9) a = Da * ( /D)= 0.5 / 0.8 = 0.6 in

  28. Frost Heave Ground swell due to water volume expansion on freezing regular and < 50 mm (minor) Water rise by capillary action and formation of ice lenses irregular and of the order of 300 mm (major) Surface down thawing leads to super saturation foundation becomes very weak until drained

  29. Conditions for Frost Heave Freezing temperatures usually natural, artificial also Source of water ground water table Frost susceptible soil (Table 2.3, Coduto) silts and fine sands - F4 soils

  30. Measure to mitigate frost heave Insulate - rare Remove / replace - not common Place foundation below depth of heave, Df most common

  31. Df is depth of frost penetration Varies by geographic location (Fig. 2.12, Coduto) Syracuse ~ 1.4 m Minnesota ~ 2.5 m California and Southern States < 0.3 m Consult local practice, building codes

  32. Other water related problems Scour (armour, riprap) Corrosion (coating, cathodic protection) Sulfate attack (special cement, low w/c ratio) Decay, insects and fire (creosote pressure treat)

  33. Soils 75 - 5 mm Gravel 5 - 0.075 Sand < 0.075 Silt and Clay Coarse #200 #200 Fine Grain size vs plasticity and liquid limit

  34. mass volume Va Ma air voids Vw Mw water minerals Vs solids Ms Soil

  35. Coarse grained soils e = void ratio = Vv/Vs emax and emin Dr = relative density = {(e-emin)/(emax-emin)}*100

  36. Fine grained soils Water content = w = (Mw / Ms)*100 SL = shrinkage limit PL = plastic limit LL = liquid limit w = natural water content

  37. Coarse grained soils emax e emin Fine grained soils w PL LL

  38. Gravel Sand Silt Clay

  39. Gravel Sand Silt Clay Gravity G Wellpoint V Wellpoint Electro-osmosis?

More Related