1 / 33

Photometry of LED Lighting Devices

Photometry of LED Lighting Devices. Tony Bergen. Contents. Introduction – Specific Issues with LEDs IES LM-79-08 Current CIE Activities. Introduction – Specific Issues with LEDs* * And solid-state lighting devices in general. What’s good?. Long lifetime Robust “Tuneable” colours

tekli
Download Presentation

Photometry of LED Lighting Devices

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Photometry of LED Lighting Devices Tony Bergen

  2. Contents • Introduction – Specific Issues with LEDs • IES LM-79-08 • Current CIE Activities

  3. Introduction –Specific Issues with LEDs** And solid-state lighting devices in general

  4. What’s good? • Long lifetime • Robust • “Tuneable” colours • (Becoming) highly energy efficient

  5. What’s not so good? • Output is very temperature dependant • Poor design gives shorter life • Issues with luminance/glare • Good photometry is harder

  6. Photometric Challenges • Quasi-monochromatic spectra means good quality photocells are more important than ever …

  7. Photometric Challenges • Pulse-width modulated light causes timing and measurement issues • Long stabilisation time • Ambient temperature sensitivity • Absolute photometry instead of Relative (cd/klm)

  8. Photometric Challenges • Directionality of light output of LEDs can cause inverse-square law to fail at shorter test distances …

  9. Inverse-Square Law Eg: Divergent LEDs on a linear luminaire

  10. Inverse-Square Law Consider a 1200 mm luminaire measured at 6 metres (5 : 1) • Beam incorrectly measured • Inverse square law doesn’t apply •  I  E x d2

  11. Photometric Challenges • Sometimes need to use CIE recommendations* for floodlight photometry to calculate required test distance* CIE Publication no. 43 “Photometry of Floodlights”

  12. IES LM-79-08Electrical and Photometric Measurements of Solid-State Lighting Products

  13. IES LM-79-08 • Specification released in 2008 • Extra-special consideration given to: • Ambient (environmental) conditions • Spectral properties • Thermal characteristics • Gives guidelines for measurement in integrating sphere and goniophotometer

  14. Integrating Sphere Photometry • Sphere with inside diffuse, high reflectance white • Light output from test lamp is compared with light output from reference (known) lamp • Measure luminous flux, luminous efficacy and spatially-averaged chromaticity

  15. Integrating Sphere Photometry LM-79 says: • Two geometries (also specified by CIE 84): • 4 (full sphere) • 2 (hemisphere)

  16. Integrating Sphere Photometry • For 2 geometry, plug the gap or have a darkened room behind • If plugging the gap, make sure that the cover disk doesn’t extract heat from the device

  17. Integrating Sphere Photometry • LM-79 suggests two methods of measurement: • Sphere-photometer uses a traditional photocell and picoammeter or equivalent (beware spectral mismatch) • Sphere-spectroradiometer uses a spectro to measure both flux and chromaticity (recommended method)

  18. Integrating Sphere Photometry • Match reference lamp and test lamp as closely as possible • Make sure the internal temperature is within 25° ± 1°C • Calculate spectral mismatch correction factors if necessary • LM-79 slightly more relaxed on sample size for given sphere size than CIE 84

  19. Goniophotometry • A goniophotometer measures luminous intensity distribution and chromaticity distribution • Can derive luminous flux etc. • Has advantage of being absolute measurement

  20. Goniophotometry LM-79 says: • Make sure test distance is sufficiently long so that the inverse square law applies • Make sure test angle increments are sufficiently small to make measurement accurate • Keep room temperature within 25° ± 1°C • Calculate spectral mismatch correction factors if necessary

  21. Goniophotometry • Measure chromaticity: • In steps of 10° in elevation angle • In two orthogonal C-planes 0° and 90° • Calculate spatially-averaged chromaticity, weighted by: • Luminous intensity in each direction • Solid angle

  22. Spatial non-uniformity of chromaticity • Deviation of chromaticity from spatial avg

  23. Spatial non-uniformity of chromaticity • Deviation of chromaticity from spatial avg Spatially averaged colour temperature = 5870K

  24. Spatial non-uniformity of chromaticity • Deviation of chromaticity from spatial avg Spatially averaged coordinates: u’ = 0.2051, v’ = 0.4716

  25. Current CIEDivision 2 Activities

  26. TC2-50 • Measurement of the Optical Properties of LED Clusters and Arrays • This is the main standard that we want to see completed • It will cover similar aspects to the IES LM-79-08 • Has been held up in the past due to arguments over definitions and changed chair twice • From Budapest meeting 2009 we now have a promising way forward

  27. TC2-58 • Measurement of LED Radiance and Luminance • This is a difficult area of measurement because LEDs are small and directional • Some similarities with laser safety

  28. TC2-63 • Optical measurement of High-Power LEDs • CIE 127 “Measurements of LEDs” already covered low power LEDs • This standard will look at measurement of individual high power LEDs, as opposed to LED clusters and luminaires

  29. TC2-64 • High speed testing methods for LEDs • Looking into test methods for production-line testing of LEDs • Want to make measurements consistent and comparable between labs

  30. TC2-66 • Terminology of LEDs and LED Assemblies • This TC is looking in to terminology for different types of LEDs and LED packages • Will be used to create appendices for the TC2-50

  31. TC2-65 • Photometric measurements in the mesopic range • This is important for photometry of street lighting luminaires where their application will often be in the mesopic range • The mesopic range favours white LED sources compared with traditional HPS streetlights

  32. Reporterships • R2-42 Measurement for LED Luminaries • R2-43 Measurement of Integrated LED Light Sources • R2-44 Photometric Characterisation of Large Area Flat Sources used for Lighting

  33. Tony Bergen Technical Director Photometric Solutions International Factory Two, 21-29 Railway Avenue Huntingdale, Vic, 3166, Australia Tel: +61 3 9568 1879 Fax: +61 3 9568 4667 Email: tonyb@photometricsolutions.com Web: www.photometricsolutions.com Thank youfor your kind attention

More Related