1 / 19

QUALITY CONTROL ANALYSIS

QUALITY CONTROL ANALYSIS. STATISTICAL QUALITY CONTROL WHAT IS SQC??. SQC is a mathematical study used to investigate a manufacturing process to determine its precision and accuracy. It is used to check and improve the quality control of a manufactured part.

thuy
Download Presentation

QUALITY CONTROL ANALYSIS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. QUALITY CONTROL ANALYSIS

  2. STATISTICAL QUALITY CONTROLWHAT IS SQC?? • SQC is a mathematical study used to investigate a manufacturing process to determine its precision and accuracy. • It is used to check and improve the quality control of a manufactured part. • Ensure products or services are designed and produced to meet or exceed customer requirements and expectations.

  3. USING THE STATISTICAL PROCESSCONTROL ANALYZER

  4. SPC EQUIPMENT DIGITAL CALIPER POWER SUPPLY CABLE SPC PROCESSOR

  5. NEVER GONNA LET YOU DOWN DIGITAL CALIPER PARTS INSIDE MEASURING JAWS LOCK SCREW DIGITAL WINDOW MEASURING THUMB SCREW DEPTH MEASURING OUTSIDE MEASURING JAWS

  6. CABLE CONNECTED TO SPC ANALYZER NEVER GONNA RUN AROUND AND DESERT YOU Cable tab lines up with slot in socket

  7. NEVER GONNA MAKE YOU CRY SPC ANALYZER BUTTONS Clear entry Clear limits Enter data Enter upper & lower tolerance limits Statistical analysis of entered data Feed paper tape

  8. ABBREVIATIONS FOR STATISTICAL DATA TERMS • USL - Upper statistical limit of tolerance • LSL - Lower statistical limit of tolerance • N - Number of samples taken or data points • Max - Maximum value of largest sample Taken • Min - Minimum value of smallest sample Taken • R - Range of values taken

  9. More Abbreviations • X bar - Mean of all samples taken • O n - STANDARD DEVIATION OF ENTIRE population of samples • O n-1 - Standard deviation of a sample of entire population • P - Percentage of defective samples (Parts out of specs) • Cp - PROCESS CAPABILITY SHOWS precision of process • Cpk - Process capability shows both accuracy & precision

  10. SPC ANALYSIS STEPS USING TOLERANCES • Press (CL) key to clear limits • Press (TOL LIM) key to set upper and lower statistical limits of tolerance used • Zero digital caliper • Manually set caliper to upper statistical limit • Press (data) key to set USL (will show on tape as (lmt) • Manually set caliper to lower statistical limit • Press (data) key to set LSL (will show on tape as (lmt)

  11. The rest of the Steps • Press (TOL LIM) key to show tolerance limits on paper tape as (usl) and (lsl) • Now use the digital caliper to enter measurements of the sample and press the (data) key each time • Repeat above step at least 10 times to get 10 samples • Press (stat) key to perform a statistical analysis of all the samples entered • Press (feed) key after printing stops to advance paper

  12. SETTING UP SPC Press (ON) key Tape will show *Print On* Press clear limit (CL) then total limit (TOL) tape shows *Limit Clear*

  13. SETTING UP SPC • Turn (on) caliper • Slide jaws together • Press zero key

  14. SETTING UPPER TOLERANCE LIMIT Manually set USL of .115 thousands on caliper then press DATA key. This will show on tape as (lmt)

  15. SETTING LOWER TOLERANCE LIMIT Manually set LSL of .105 thousands on caliper press data key. This will show on tape as (lmt)

  16. CHECKING TOTAL LIMIT Now press total limit key the tape should read as shown below with a tolerance of .010 or USL-LSL *NEW LIMIT DATA* LSL 0.1050 USL 0.1150 TOTAL LIMIT .010

  17. MEASURED SAMPLES OF A PART Take 10 measurements of the part by pressing the data key after each measurement. This can be done in two different ways as shown. Sample being measured in 10 spots

  18. ANALYSIS OF DATA TAKEN Data analysis is printed on paper tape After all measurements are taken with the caliper and entered into the (SPC) press the (STAT) key for a full analysis of data

  19. THE TAPE Limits Tolerance Readings Histogram Statistical data

More Related