1 / 22

Using the SDR-IQ for EME

Using the SDR-IQ for EME. Using the SDR-IQ for EME Application to random QSO’s with JT65 by Edward Cole – KL7UW. Recent years have seen increasing use of computers in the EME station: Antenna Control / Tracking Software Radio Control Design and Engineering Analysis Tools DSP

tranquilla
Download Presentation

Using the SDR-IQ for EME

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Using the SDR-IQ for EME

  2. Using the SDR-IQ for EMEApplication to random QSO’s with JT65by Edward Cole – KL7UW Recent years have seen increasing use of computers in the EME station: • Antenna Control / Tracking Software • Radio Control • Design and Engineering Analysis Tools • DSP • Waterfall & Spectrum Displays • Digital Modes • Migration to Internet scheduling: e-mail & loggers • Software Defined Radios

  3. Software Defined Radios Amateur Radio is beginning to experiment with SDR’s (software defined radios): • Recent Examples: SDR-14, SDR-1000, DSP-10, USRP, FLEX-5000 • Fall 2006 RFSpace introduced the SDR-IQ; a software defined receiver that covers 500-Hz to 30-MHz • Single 3.75 inch square pcb • Interfaced and powered thru computer’s USB-2.0 port • 200 Demo Boards offered at end of 2006 for $375 • I had to have one!

  4. The SDR-IQ • Minimal RF hardware; Direct convertion to base-band which is converted to digital data and transferred to the USB port • Entire LF-HF band is sampled at 66.66 MHz by AD6620 at 23 bits • 16 bits of I/Q data is transferred • Processed by software to recover virtually any modulation type. • DSP filtering & NB detection

  5. Covers 500-Hz to 30-MHz in 1-Hz steps Clipping level > -4 dBm Image Rejection 80-dB IP3 (typ) +15-dB 5 Vdc at 425 mA Ext. Radio control via DB-9 Open source Active-X Drivers: Win/Linux/Mac Network server for remote operation of SDR-IQ Spurious -80 dBfs, -100 typ 28-MHz noise floor -134 dBm 28-MHz MDS-133 dBm/Hz No freq drift measured Shielding Test at 20-MHz: -111 dBM (5w @ 25-feet) -100 dBm (50w @ 25-feet) 190-KHz displayed real-time Minimum RBW: 0.75 Hz for BW=190 KHz 0.031 Hz for BW=5 KHz Spectravue software provided SDR-IQ Specs

  6. Software • RFSpace provides Spectravue for immediate use of the SDR-IQ. • Modes: CW, CWr, SSB,DSB, WBFM, NBFM, AM • Displays: raw signal, 2D and 3D spectrum, waterfall, combo 2D+waterfall, total power, and IQ phase • SW controls: sample size, smoothing, amplitude scale, RF & Demod freq, mode, filter bw, NB and AGC • Alberto, I2PHD offers a SDR-IQ driver for Winrad (windows version of Linrad) which is written for weak-signal/EME. • Winrad modes: CW and SSB, only, but with more settings for improved audio reception of weak-signals. • Displays for both are both shown, later • Refer to their websites for more details

  7. Using the SDR-IQ for 144-MHz EME • To use the SDR-IQ for EME I bought a DEMI 144/28 transverter (only receive side used). • I added a 18-dB mmic WBIF amp in between them. • Simulations using a signal generator input to my 2nd 2m preamp I get: -18 on JT65 with -141 dBm -26 on JT65 with -150 dBm -28 on JT65 with -152 dBm • The JT65 readings were obtained with my FT-847 plus soundcard with JT65B/Spectra-JT running. • This provided comparison of the SDR-IQ to JT65

  8. Using the SDR-IQ for 144-MHz EME Figures 1-6 are made with the signal generator input: • Fig-1 shows typical JT65 screen • Fig-2 Winrad, no IF amp, BW=50 KHz, RBW=3.4 Hz, display is 3-KHz wide, signal= -150 dBm • Fig-3 Winrad plus IF amp, BW=50, RBW=3.4, display 3-KHz, signal= -166 dBm • Fig-4 Winrad BW=50, RBW=54.3, -150 dBm input • Fig-5 Not shown • Fig-6 Winrad BW=100, RBW=1.7, -150 dBm input

  9. Using the SDR-IQ for 144-MHz EME Figures 7-12 are actual EME signals: • Fig-7 K6MYC on JT65, -21 signal • Fig-8 K6MYC on Winrad, BW=5 KHz, RBW=2, -17 signal • Fig-9 K6MYC on Winrad, BW=50, RBW=3.5, -24 signal • Fig-10 WE9Y & WQ5S on JT65, -22 and -20 signals • Fig-11 WE9Y on Winrad, BW=26, RBW=9.2, -20 signal • Fig-12 The 144.100-144.150 MHz EME band at KL7UW

  10. SUMMARYClearly the SDR-IQ will display most JT65 signals over a wide enough band to cover EME activity and randomly detect digital stations! • Economical viewing of EME sub-band • Up to 100-KHz displayed on moderately fast computers • Full 190-KHz with CPU > 2-GHz. • Enables random digital EME contacts • K1JT working on blend of JT65 and Linrad to decode all stations in 100-KHz band. • Cost $499 with enclosure plus $170 for 144-to-28 MHz conv. • Limitations are what software designers can think of! • http://www.kl7uw.com/SDR.htm

More Related