1 / 3

MILK PASTEURIZER

MILK PASTEURIZER. MILK PASTEURIZER

verne
Download Presentation

MILK PASTEURIZER

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. MILK PASTEURIZER

  2. MILK PASTEURIZER One milk pasteuriser with a capacity of 300 -400 litres of milk for hours, HTST type with an operate range from 75° to 95°C, including milk receiving tank of 100 litres with level control. The pasteuriser is complete with flow meter on the milk to be pasteurised . The flow milk indicates both the flow rate and the pumped volume on a remote digital display. Milk pump centrifugal pump of 2 Hp , in line stainless steel filter and flow gauge , precise flow control valve and out let temperature control valve, three cell heat exchanger for regeneration , heating and cooling. Air actuated 20 second holding tube , plus additional tubes allowing an holding time up to two minutes. Hot water system with centrifugal water pump Electronic controller with thermostat for milk and water temperature , control panel with electronics thermostat control and illuminated control switches temperature recorder of milk pasteurisation and cooling temperature. The unit is mounted on a stainless steel platform equipped with wheels and necessary milk hoses of 5 meters each length. Power consumption 20 Kw – 30-40 Amps 400 V three phases Air compressed consumed 30 nl/min at 5 bar. The pasteurisation unit has a capacity of 300- 400 able to perform the following thermal cycle Fresh milk 4-50-75 ( 95) -4°C – holding time 20- 120 sec composed by: * 100 litres buffer tankfor milk storage Made in AISI 304 stainless steel, with the following characteristics: - AISI 304 stainless steel tank, with glazed and pickled inside and outside surface - Pickled, flattened, grounded and spotted welding - Conical bottom with total discharge - Plate cover with CIP (cleaning in place) devices. - Total discharging piping, manufactured in stainless steel - three legs supporting structure manufactured in stainless steel - level probe Centrifugal pump with sanitary close impeller manufactured in stainless steel aisi 304 , connection DN 25. Capacity 400 lt/h complete with valve to adjust the capacity Installed power: 1,5 Kw Milk strainer- line filter manufactured in stainless steel aisi 304 with connection with centrifugal pump. The filter will be placed on a frame in stainless steel, it is easy to clean and to open for maintenance. The cartridge is manufactured in stainless steel with hole of 0, 5 mm or different on request. DIN connection * Plate pasteuriser Plate pasteuriser designed for the treatment milk see above the cycles: The machine is composed of: 3 sections plate pasteuriser with a capacity of 300 Lt/h of product heating section from 4°C to 50°C using product in counterflow pasteurisation section from 50 to 75 or 95 or with hot water - pre cooling product section from 75 or 95 to 29 or 49 °C with product in counterflow (heating recovery system) Cooling section from 49 or 29 to 4°C with chilled water at +2°C.

  3. The exchanger is composed of: Plates in stainless steel AISI 316 and nitrile alimentary rubber joints - Intermediate plates in stainless steel AISI 304 - Frame covered in stainless steel AISI 304 with closing lateral tie rod - Pipe connections for various fluids in stainless steel - Thermal holding system for 20 or 120 seconds with multiple pipes. The pipes are connected in serial with detachable turns and mounted on a supporting frame in stainless steel. - Hot water at 97°C or different temperature adjustable group formed by a pneumatic valve, pipes, and manual valve, tank with 20 Kw electrical resistances, hot water pump, safety valve. Chilled water at +2°C adjustable group formed by a pneumatic valve, pipes, and manual valve. - Instruments to record the pasteurising and the exit temperature - System to adjust the thermal fluid temperatures - 3 ways valve to divert the product in case of low temperature - Necessary electro pneumatical transducers - PT 100 probes for temperature measurements - Air reducing equipment for compressed air - Electrical control board with temperature indication, control and record on paper Consumption’s: Electrical Power: 22 kW Water: 1,0 m3/h equal to 18.000 Kcal. Compressed air: 40 NLP / minute at 5 bar TECMON S.R.L. P.IVA 00791710965 VIA LEONARDO DA VINCI, 11/B COD.FISC. 04821200153 20060 CASSINA DE’ PECCHI (MI) TEL. +39 0295299106 CAP. SOC. € 83.000,00 INT. VERS. FAX +39 0295299315 ISCR. TRIB. DI MONZA REG. SOC. 17929 E-MAIL : tecmon@tin.it C.C.I.A.A. MONZA E BRIANZA 1041916 E-MAIL : info@tecmon.it http:// www.tecmon.it

More Related