1 / 52

SNM940 – 3D Project Monitoring Quick Start Guide

SNM940 – 3D Project Monitoring Quick Start Guide. 28 February 2011. Process. Order Hardware & Add-Ons Create Customer Order Services Generate Passcode Replace SIM Card Configure Device Set up TCC Configure Display (CB430, CB450, CB460) Set up BC Set up VL. Reference Documents.

virote
Download Presentation

SNM940 – 3D Project Monitoring Quick Start Guide

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. SNM940 – 3D Project MonitoringQuick Start Guide 28 February 2011

  2. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Replace SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  3. Reference Documents • SNM940 Install Guide • iStore Guide • TCC Guide • VisionLink Getting Started Guide for 3D Project Monitoring • Business Center Help Files

  4. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Replace SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  5. Ordering SNM940 Hardware • Login to Trimble SITECH Software Solutions Store • Select SNM940 Tab • Select SNM940 HW • (Part # 80632-30-HH) DCM300G/ SNM940, Connected Site Gateway, GSM • (Part # 80632-10-HH) SNM940, Connected Site Gateway, Verizon GSM = Worldwide support (where certified). Customer supplies SIM card & data plan Verizon = US only. Trimble supplies data plan as part of subscription

  6. Hardware Options • In addition to the SNM940 – also need to order • Wiring Harness – Basic • GPS/Cellular Combination Antenna • WLAN Antenna for WiFi • Press “Add to Cart” Antenna options

  7. Placing order • In “Your Shopping Cart”: Confirm Order • Press “Checkout” • Confirm Shipping Method & Address • Press “Continue Checkout” • Enter PO # • Press “Continue Checkout” • Accept Terms ofSale • Review Order • Press “Place Order” • Confirmation will appear • Print for your records

  8. Order Fulfillment • Once the Hardware order has been placed, it takes up to 48 hours for the HW to appear in the “Initiate Services” tab • Manual Order Processing at Trimble • Credit Check • Order Fulfillment & Shipping • Once the order is shipped, then the S/N of the device is known, which is needed to Add Services • If the Hardware doesn’t appear in 48 hours, send email to TCM_support@trimble.com with order number

  9. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Replace SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  10. Create Customer • Click the “Initiate Service” tab • Click “Add New Customer” button

  11. Create Customer • Add Appropriate Information & press “Apply”

  12. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Replace SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  13. Ordering Services • Click the “Initiate Service” tab • Search for Device to add Services To • Type “SNM940” in Device Field • Click “Search” for list of available devices

  14. Ordering Services • Select Customer from “New Owner” field • Select Device and fill in first 4 fields (required) • Make • Model • Year • Serial #

  15. Ordering Services • Select 3D Project Monitoring Service: • VisionLink Universal Subscription • VisionLink 3D Project Monitoring Subscription • TCC Device License • SNM940 Connected Machine Option • SNM940 3D Project Monitoring Option • Optional VL Plans: • Health • Utilization • Rapid Reporting • Add to Cart

  16. Ordering Services • 2 other options for SNM940 devices • Telematics Only • VisionLink Universal subscription • Optional Health subscription • Optional Utilization subscription • Optional Rapid Reporting subscription • 3D Connected Machine • SNM940 Connected Machine Upgrade • TCC Device License • All VisionLink telematics subscriptions are optional • Universal subscription • Health subscription • Utilization subscription • Rapid Reporting subscription

  17. Ordering Services • After clicking “Add to Cart” • Click “OK” on pop-up • Follow same process for Placing the Order as HW

  18. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Replace SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  19. Option Passcodes • You will need to retrieve and upload a Passcode for your SNM940 device to work properly for 3D Project Monitoring • Select the Option Passcodes tab

  20. Option Passcodes • From the Option Passcodes tab: • Filter screen by order number (if needed) • Click “Enter Value” in the Serial # column • Enter Device Serial Number • Click “Apply” or “Apply & Email” to generate passcode • 555656-TRG41-00000-DD7F5508

  21. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Cell Connectivity & Replacing the SIM Card • Configure Device • Configure Display (CB430, CB450, CB460) • Set up TCC • Set up BC • Set up VL

  22. Cell Connectivity • Cell Connectivity does not enable immediately upon ordering services: • CDMA devices take up to two hours to establish cell connectivity • GSM devices have the SIM card disabled for 3D Project Monitoring due to the high data transfer requirements • It is the customer or dealer’s responsibility to get a SIM card from their local wireless provider • SIM card should support monthly data rates of a minimum of 1 GB – 2 GB recommended

  23. Replace SIM Card for GSM Devices • Open back of SNM940 • Pull out SIM tray • Remove SIM and place new SIM in tray • Replace Tray • Replace the back of SNM940 See SNM940 Install Guide for more details On replacing the SIM

  24. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Cell Connectivity & Replacing the SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  25. Configure the SNM940 Device • IMPORTANT: before installing the SNM940 device or taking it to the field, the device must be configured and tested in the office • Use the Trimble Web Interface Utility to configure the SNM940 device • Connect the Web Interface Utility to the SNM940 via the WiFi • The SNM940 must have the following connected • Power + • Power – • Keyswitch • WiFi Antenna • GPS/Cellular Antenna

  26. Configure the SNM940 Device • Ensure SNM940 is on and fully powered up • Allow approximately 3 minutes for this to happen • From your computer’s Wireless Center, connect to the SNM940 device • Trimble Service (##########) • # = Serial Number of Device • A pop-up window will appear,requesting a password • abcdeabcde Allow approximately 3 minutes to connectto the SNM940 WiFi

  27. Configure the SNM940 Device • Open Web Browser & Enter IP address of Trimble Web Interface Utility • 192.168.33.1 Trimble Web Interface Utility Home Page

  28. Configure SNM940 Device • Enable Lock Code • Go to the “Option Enabled” tab • Only WiFi will say Enabled • All others will say Not Enabled • Enter the Passcode received from the iStore into the “Enter Lock Code” field and press “Submit” “Cellular Parameter Modification” does not pertain to CDMA GSM: Top 4 enabled CDMA: Items 2, 3 & 4 enabled

  29. Configure the Serial Port • To enable the Serial Port to work with CB430, CB450 & CB460 • Click the “Home” tab • Select “Serial Port” • Select the “PPP Connection” radio button • Set the Baud Rate to • 57600 & press “Submit”

  30. Configure New SIM for GSM • Click “Cell” Tab • Click on APN – it will ask for a password • adminPassword adminPassword

  31. Configure New SIM for GSM • Select your provider from the “New APN” drop down • If your provider is not on the list, enter the following info provided by your mobile provider & click “Submit” Pin (4 digits) APN Username Password

  32. Configure New SIM for GSM • Click “Cell” and confirm SIM is enabled • Wait approximately 2 minutes to for this to appear • Cell RSSI should be between • -50 to -100 for good cell coverage

  33. Reboot SNM940 • Go to Home screen • Select “Reboot” • Press the “Reboot” button • - Wait 5 minutes for the SNM940 to Reboot • - Wait an additional 3 minutes for your • computer to reconnect to the SNM940

  34. Confirm Changes • Log back into the Web Interface Utility • Confirm that your computer is connected to the SNM940 • In your web-browser, re-enter the IP address In the Cell tab, confirm your APN is selected In the Option Enabled tab, confirm the correct items are enabled

  35. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Cell Connectivity & Replacing the SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  36. Configuring TCC • A TCC account will automatically be created if the customer does not have TCC and this is their first TCC Device License • The Dealer and Customer will receive an email Linda Chase, TCC Product Manager • Contains url, username/password & training instructions

  37. Log In To TCC • www.myconnectedsite.com/hce • Enter Username, Organization & Password from email • From the TCC Home screen, select: Administration  Manage Devices

  38. Connect the Device to TCC • In “Manage Devices”, click “Add Device” button • In “Add Device”, click “Type:” down arrow • In “Select Device Types” dialog • Click: Trimble  Heavy Civil Construction  Device Type Device Type: - CB430 - CB450 - CB460 Click Save

  39. Connect the Device to TCC • In Add Device dialog, “Type:” is now filled in • Enter Device (CB430, CB450, CB460) Serial Number • Enter & Confirm Password (user generated) • Click “Save” button • Device is added to “Manage Devices” dialog All other fields are optional Click “Close” and Log Out of TCC

  40. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Cell Connectivity & Replacing the SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  41. Machine Control Display • The CB430, CB450, CB460 Display needs to be configured to communicate with TCC • Enable WiFi/Cell Communications with SNM940 • In Config  Machine Settings  Wireless Communications: set to Wi-Fi/Cell (SNM940) Click: “Edit Machine” Click: Menu Button Select: “Machine Settings” and “OK” Click: Installation Button Arrow Down to: “WiFi/Cell (SNM940)” Click: “Finish” Once the display Returns to the “Machine Settings” page, click “Esc” Arrow to the: “Wireless Communications” page Continue to Arrow to the “Finished” screen

  42. Machine Control Display • The CB430, CB450, CB460 Display needs to be configured to communicate with TCC • In Installation  Connected Community Settings set: Organization TCC Password Enable Auto Sync Click: Auto Sync Disable

  43. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Cell Connectivity & Replacing the SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  44. Create Project in Business Center • Create New Project in Business Center • Select Template • Drag Data to Project • Add TCC Location • External Services Enter TCC Info: - User Name - Organization - Password Click OK

  45. Create Project in Business Center • Field Data  Create Job Site Design • Save Project Enter Design Name: Click “Close” Tick “Synchronize” Box Click “OK”

  46. Create Project in Business Center Select TCC Filespace • Publish Project TCC Tick: - Publish project file - Publish layers Create or Browse TCC Folder Click “OK”

  47. Process • Order Hardware & Add-Ons • Create Customer • Order Services • Generate Passcode • Cell Connectivity & Replacing the SIM Card • Configure Device • Set up TCC • Configure Display (CB430, CB450, CB460) • Set up BC • Set up VL

  48. Create Project in VisionLink • Log Into VisionLink • www.myvisionlink.com • Confirm Asset in the Fleet Summary page • Last Known Status = “Reporting” Create a new Project Administration  Manage Projects

  49. Create Project in VisionLink • Manage Projects: select New Project • Enter New Project Details • Create Connection to TCC Business Data Center • Select Jobsitecreated in BC Title Project Start Date Project End Date Project Time Zone Enter TCC Info: - User Name - Organization - Password Click “Next – Boundary” Click “Save” This is the Project created in BC

  50. Create Project in VisionLink • Draw boundary around entire Project Area • Select the Coordinate System for the Project • Use the Drop-Down list to select the coordinate system related to your Project • Or browse yourcomputer Boundary is used to identify the Project that Tag files belong to, so it should be slightly larger than the actual project Click “Next – Coord System” Click “Done – Save and Close” If you set up a project in BC, there should be a Coord System file (.dc or .cal) inthe Business Data Center

More Related