1 / 10

Excel ETM 2VS Basic Operation Manual

Excel ETM 2VS Basic Operation Manual. Excel ETM 2VS Basic Operation Manual. 1) Mounting Tool Holding Device and Tool in Spindle 2) Spindle Speed Selection and Operation 3 ) Table Feed (Longitudinal) Manual/Automatic 4 ) Table Feed (Cross-Slide) Manual/Automatic

willem
Download Presentation

Excel ETM 2VS Basic Operation Manual

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Excel ETM 2VS Basic Operation Manual

  2. Excel ETM 2VS Basic Operation Manual 1) Mounting Tool Holding Device and Tool in Spindle 2) Spindle Speed Selection and Operation 3) Table Feed (Longitudinal) Manual/Automatic 4) Table Feed (Cross-Slide) Manual/Automatic 5) Table Feed (Vertical) Manual/Automatic 6) Setting Digital Readout 7) Quill Feed Manual Operation 8) Quill Feed Automatic Operation

  3. Mounting Tool Holding Device in Spindle 1 B • This milling machine uses R8 spindle and arbours (tool holding device). • To mount the arbour in the machine insert arbour (A) up inside Spindle (B) and rotate it to insure key in spindle aligns with Keyway (C) on arbour , this will allow arbour to fully insert into spindle, diagram 1. • Rotate draw bar (D) located on top of vertical head by hand until fully hand tight (arbour should now be held in place inside spindle), diagram 2. • Place correct size spanner (19mm) on draw bar and pull spindle brake (E) located on left hand side of vertical head down then tighten draw bar using ratchet spanner, diagram 3. • note Draw bar does not need to be tightened to excess. A C 2 D 3 E

  4. Spindle Speed Selection and Operation B A To select a high gear ratio rotate motor speed selector switch (A) on control panel to the left and push gear box selector lever (B) on right hand side of vertical head in and rotate to face forward as in diagram (1) To select a low gear ratio rotate motor speed selector switch (A) on control panel to the right and push gear selector lever (B) on right hand side of vertical head in and rotate to face rear of head as in diagram (2) To change spindle speed press Green spindle start button (C) on control panel and rotate variable speed handle (D) on right hand side of head clockwise to increase spindle speed or anti-clockwise to decrease spindle speed as in diagram (3) Spindle Speed can be seen on speed indicator on front of head as in diagram (4) in this example if high gear ratio selected (E)1600 RPM if low gear ration selected (F) 180RPM To stop spindle press Red spindle stop button (G) on control panel as in diagram (5) (1) (2) (3) (4) (5) B A C D F E G

  5. Table Feed (longitudinal) Manual/Automatic To move table manually in a longitudinal direction rotate handle (A) on end of table clockwise to move from right to left or anti-clockwise to move from left to right, see diagram (1). To move table automatically in a longitudinal direction set correct feed rate by rotating knob (1) on feed motor (clockwise to increase speed or anti-clockwise to decrease speed), diagram (2) To engage feed move lever (2) on feed motor to the left to give right to left movement diagram (3) Move lever to the right to give left to right movement, diagram (4) To disengage return to centre position diagram (2) For safety fold handle on end of table in before engaging automatic feed 1) 2) 3) 4) A 1 2

  6. Table Feed (Cross-Slide) Manual/Automatic To move table cross-slide manually rotate handle (B) on front of table clockwise to move table forward or anti-clockwise to move table backwards see diagram 1. To move table cross-slide automatically set correct feed rate by rotating knob (1) on feed motor (clockwise to increase speed or anti-clockwise to decrease speed), diagram (2) To engage feed, move lever (2) on feed motor up to give forward movement of cross-slide diagram (3) Move lever down to give backwards movement of cross-slide diagram (4) To disengage return to centre position diagram (2) For safety fold handle on front of table in before engaging automatic feed 1) 2) 3) 4) B 1 2

  7. Table Feed (Vertical) Manual/Automatic To move table in a vertical direction manually push handle (C) on knee in to engage teeth on handle with teeth on spindle, then rotate clockwise to raise table or anti-clockwise to lower table see diagram 1. To raise table automatically set correct feed rate by rotating knob (1) on feed motor (clockwise to increase speed or anti-clockwise to decrease speed), diagram (2) To engage feed, move lever (2) on feed motor up to raise the table using automatic feed diagram (3) Move lever down to lower table using automatic feed diagram (4) To disengage return to centre position diagram (2) 1) 2) 3) 4) C 1 2 3

  8. Setting Digital Readout 1) 2) 3) 4) 1) Whenmachine is turned on the digital readout will perform an internal memory check and reset to last settings used. To reset the readout when datum has been established on work piece press the button for the axis you wish to set and the readout next to that axis will go blank (X axis) in example diagram (1) 2) Press the 0 button on the panel and a single 0 will then appear next to the X axis diagram (2) 3) Press the enter button (ENT) on the panel this will then set the X axis to Zero and 0.000 will appear next to the X axis diagram (3) 4) To set any other value repeat the above steps above using the value required for example 6.500 and this will appear next to the axis diagram (4)

  9. Quill Feed Manual Operation 1 • Machine can be used for drilling operations by use of the quill to plunge into the material. • To operate quill feed manually release the quill lock (A) on the front of the vertical head by rotating it anti clockwise, diagram 1 • Turn on the spindle and rotate the quill operating lever (B) on the right hand side of the vertical head in a clockwise direction to feed the drill/cutter into the work piece, diagram 2. • When released handle automatically return to its original position. • For greater travel of the quill, lock quill, pull lever out to the right, rotate anti-clockwise and re-engaged with the next set of holes on the spindle then release lock to continue drilling. A 2 B

  10. Quill Feed Automatic Operation 1 A • To operate quill automatically turn off spindle and rotate feed lever (A) on right hand side of vertical head anti clockwise to IN position diagram 1 • Rotate quill feed rate lever (B) on left hand side of vertical head clockwise to appropriate speed (0.076mm/0.03”) per revolution in example, diagram 2 • Push quill feed direction lever (C) on front of vertical head in to ensure downwards feed, diagram 3. • Turn spindle on, pull quill feed lever (D) on front of vertical head to the left to engage feed, diagram 3. • When drilling is complete push quill feed lever (D) to the right to disengage feed, diagram 4 B 2 3 C D 4

More Related