1 / 28

Longitudinal Matching , or How to move things around by a hairs-width at the speed of light….

Longitudinal Matching , or How to move things around by a hairs-width at the speed of light…. E. E. E. E. f. f. f. f. E. E. f. f. Longitudinal Matching Scenario. DC Gun. Requirements on phase space: high peak current (short bunch) at FEL bunch length compression at wiggler

xanthe
Download Presentation

Longitudinal Matching , or How to move things around by a hairs-width at the speed of light….

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Longitudinal Matching, orHow to move things around by a hairs-width at the speed of light….

  2. E E E E f f f f E E f f Longitudinal Matching Scenario DC Gun Requirements on phase space: • high peak current (short bunch) at FEL • bunch length compression at wiggler using quads and sextupoles to adjust compactions • “small” energy spread at dump • energy compress while energy recovering • “short” RF wavelength/long bunch, large exhaust dp/p (~10%) • get slope, curvature, and torsion right (quads, sextupoles, octupoles) IR Wiggler SRF Linac Bunching Chicane Dump

  3. Why a long bunch at injection? • Space Charge… Longitudinal Space Charge…

  4. Space Charge – Esp. LSC – Down Linac • Had a number of issues in linac during commissioning: • Why was the bunch “too long” at the wiggler? • bunch length at wiggler “too long” even when fully “optimized” (with good longitudinal emittance out of injector) • could only get 300-400 fsec rms, needed 200 fsec • Why did the “properly tuned lattice” not fully compress the bunch? • M55 measurement showed proper injector-to-wiggler transfer function, but beam didn’t “cooperate”… minimum bunch length at “wrong” compaction • Why was the beam momentum spread asymmetric around crest? • dp/p ahead of crest ~1.5 x smaller than after crest; average ~ PARMELA We blamed wakes, mis-phased cavities, fundamental design flaws, but in reality it was LSC… • PARMELA simulation (C. Hernandez-Garcia) showed LSC-driven growth in correlated & uncorrelated dp/p; magnitudes consistent with observation • Simulation showed uncorrelated momentum spread (which dictates compressed bunch length) tracks correlated (observable) momentum spread

  5. Space-Charge Induced Degradation of Longitudinal Emittance • Mechanism: self-fields cause bunch to “spread out” • Head of bunch accelerated, tail of bunch decelerated, causing correlated energy slew • Ahead of crest (head at low energy, tail at high) observed momentum spread reduced • After crest (head at high energy, tail at low) observed energy spread increased • “Intrinsic” momentum spread similarly aggravated (driving longer bunch) • Simple estimates => imposed correlated momentum spread ~1/Lb2 and 1/rb2 • The latter observed – bunch length clearly match-dependent • The former quickly checked…

  6. Solution • Additional PARMELA sims (C. Hernandez-Garcia) showed injected bunch length could be controlled by varying phase of the final injector cavity. • bunch length increased, uncorrelated momentum spread fell (but emittance increased) • reduced space charge driven effects – both correlated asymmetry across crest and uncorrelated induced momentum spread • When implemented in accelerator: • final momentum spread increased from ~1% (full, ahead of crest) to ~2%; • bunch length of ~800–900 fsec FWHM reduced to ~500 fsec FWHM (now typically 350 fsec) • bunch compressed when “decorrelated” injector-to-wiggler transfer function used (“beam matched to lattice”)

  7. Happek Scan

  8. E E t t Key Points • “Lengthen thy bunch at injection, lest space charge rise up to smite thee” (Pv. 32:1, or Hernandez-Garcia et al., Proc. FEL ’04) • “best” injected emittance DOES NOT NECESSARILY produce best DELIVERED emittance! • LSC effects visible with streak camera

  9. Streak Camera Data from IR Upgrade -4o -3o -2o -5o -1o -6o 0o (t,E) vs. linac phase after crest (data by S. Zhang, v.g. from C. Tennant)

  10. Streak Camera Data from IR Upgrade +4o +3o +2o +5o +1o +6o 0o (t,E) vs. linac phase, before crest asymmetry between + and - show effect of longitudinal space charge after 10 MeV (data by S. Zhang, v.g. from C. Tennant)

  11. ±4 and ±6 degrees off crest • “+” on rising, “-” on falling part of waveform • Lbunch consistent with dp/p and M56 from linac to observation point • dp/p(-)>dp/p(+) • on “-” side there are electrons at energy higher than max out of linac • distribution evolves “hot spot” on “-” side (kinematic debunching, beam slides up toward crest…) => LSC a concern… -4o -6o +4o +6o

  12. Longitudinal Matching: The Concept • Basic idea: turn the long, low momentum spread bunch that comes out of the injector (maybe with chirp and curvature) into short bunch at the FEL • How? Parallel-to-point image in longitudinal phase space • Low momentum spread/long => “parallel” beam • Put beam through lens (linac, off crest  longitudinal focusing) and then a longitudinal drift (beamline with compaction, M56≠0 transport with nonzero compaction injected beam wiggler linac

  13. Longitudinal Matching: The Math E dE • Injected beam – with chirp and curvature { • Linac acts on injected beam { • Recirculator acts on accelerated beam { z eo dz E=Cz+Kz2 E t fo

  14. Can expand Eout-Eo in powers of dz/lRF (small parameter) Eout-Eo = dE + dz[C-DE(2p/lRF) sin fo] + dz2[K-½ DE(2p/lRF)2 cos fo] + … and shovel into zWIG, group by powers of dz and dE/Eo (another small parameter) to get zWIG = M56(dE/Eo) + T566(dE/Eo)2 + dz {1 + M56 [(C/Eo)-(DE/Eo)(2p/lRF) sin fo] +2 T566 (dE/Eo) [(C/Eo)-(DE/Eo)(2p/lRF) sin fo] } + (dz)2 { [(K/Eo)-½ (DE/Eo) (2p/lRF)2 cos fo][M56 + 2 T566 (dE/Eo)] + T566 [(C/Eo)-(DE/Eo)(2p/lRF) sin fo]2 } + …

  15. zWIG thus depends only on powers of (dE/Eo) – i.e. very small numbers - and a polynomial in dz. • Proper choice of parameters (M56, T566, fo, C, K,…) can make those terms very small – or vanish – making zWIG independent of dz – i.e., all lengths at injection go to zero offset at the wiggler: the bunch is compressed, giving high peak current Simple Case • Take C=0, K=0 and dE very small (i.e., make the injector designer’s life hard…) zWIG = dz {1 - M56 [(DE/Eo)(2p/lRF) sin fo]} + (dz)2 { [-½ (DE/Eo) (2p/lRF)2 cos fo]M56 + T566 [(DE/Eo)(2p/lRF) sin fo]2 } + …

  16. Take And get zWIG = 0 – a very compressed (and curvature corrected) bunch… Numerical Example (JLab UV FEL Driver) Eo=135 MeV, fo=-10o, DE=(135-9)/cos 10o = 128 MeV,lRF = 0.2 m M56 = (0.2/2p)(135/128)(1/sin (-10o)) = -0.193 m T566 = ½ (2p/0.2)2 (128/135) cos(-10o)(-0.193 m)3 = -3.313 m

  17. Summary: Longitudinal Match to FEL • Inject long, low-energy-spread bunch to avoid LSC problems • need 1-1.5o rms with 1497 MHz RF @ 135 pC in our machine • Chirp on the rising part of the RF waveform • counteracts LSC • phase set-point then determined by required momentum spread at wiggler • Compress (to required order, including curvature/torsion compensation) using recirculator compactions M56, T566, W5666,… • Entire process generates a parallel-to-point longitudinal image from injector to wiggler

  18. Energy Recovery • Can do the same thing to compress energy spread from FEL during energy recovery. • Bunch length compression: long bunch + small dp/p => chirped beam => compression by momentum compaction • Energy compression: short bunch + large dp/p => decompress using momentum compaction => differential energy recovery to compress energy spread

  19. “oscillator” E “amplifier” f E E E f E f f E f f Longitudinal MatchingSchematic Longitudinal Matching for ERL-Driven FEL injector linac dump wiggler

  20. Energy Recovery: Details Longitudinal Match to Wiggler • Inject long, low-energy-spread bunch to avoid LSC problems • need 1-1.5o rms with 1497 MHz RF @ 135 pC in our machine • Chirp on the rising part of the RF waveform • counteracts LSC • phase set-point then determined by required momentum spread at wiggler • Compress (to required order, including curvature/torsion compensation) using recirculator compactions M56, T566, W5666,… • Entire process generates a parallel-to-point longitudinal image from injector to wiggler

  21. Longitudinal Match to Dump • FEL exhaust bunch is short & has very large energy spread (10-15%) • => Must energy compress during energy recovery to avoid beam loss linac during energy recovery; this defines the longitudinal match to dump • Highest energy must be phase-synchronous with (or precede) trough of RF wave-form • Transport momentum compactions must match the slope (M56), curvature (T566), torsion (W5666),… of the RF waveform • Recovered bunch centroid usually not 180o out of phase with accelerated centroid • Not all RF power recovered, but get as close as possible (recover ahead of trough), because… • Additional forward RF power required for field control, acceleration, FEL operation; more power needed for larger phase misalignments • For specific longitudinal match, energy & energy spread at dump does not depend on lasing efficiency, exhaust energy, or exhaust energy spread • Only temporal centroid and bunch length change as lasing conditions change • The match constitutes a point-to-parallel image from wiggler to dump

  22. E E E t t t Energy Compression All e- after trough go into high-energy tail at dump • Beam central energy drops, beam energy spread grows • Recirculator energy must be matched to beam central energy to maximize acceptance • Beam rotated, curved, torqued to match shape of RF waveform • Maximum energy can’t exceed peak deceleration available from linac • Corollary: entire bunch must preced trough of RF waveform

  23. Higher Order Corrections E • Without nonlinear corrections, phase space becomes distorted during deceleration • Curvature, torsion,… can be compensated by nonlinear adjustments • differentially move phase space regions to match gradient required for energy compression t • Required phase bite is cos-1(1-DEFEL/E); this is >25o at the RF fundamental for 10% exhaust energy spread, >30o for 15% • typically need 3rd order corrections (octupoles) • also need a few extra degrees for tails, phase errors & drifts, irreproducible & varying path lengths, etc, so that system operates reliably • In this context, harmonic RF very hard to use…

  24. JLab IR Demo Dump core of beam off center, even though BLMs showed edges were centered (high energy tail)

  25. Nonlinearity Control Validated By Measurement Figure 1: Inner sextupoles to 12726 g-cm and trim quads to -215 g Figure 2: trim quads at -185 g with same sextupoles Figure 3: trim quads at -245 g Figure 4: quads at -215, but sextupoles 3000 g below design, at 10726 g-cm Figure 5: where we left it: trim quads -215 g sextupoles at 12726 g-cm launch f arrival f

  26. Injector to Wiggler Transport

  27. If you do it right linac produces stable ultrashort pulses Can regularly achieve 300 fs FWHM electron pulses ~150 fsec rms

  28. Injector to Reinjection Transport

More Related