1 / 33

FABRICATION OF SOLAR REFRIGERATOR

FABRICATION OF SOLAR REFRIGERATOR. GUIDED BY:- SUBMITTED BY:- KIRAN RAJ K RAVI KANT PANDEY DEPARTMENT OF RAVISH KUMAR MECHANICAL ENGG . RAJEEV KUMAR VIKAS KUMAR VIKASH KUMAR SANTOSH ABHISHEK. CONTENTS.

yuki
Download Presentation

FABRICATION OF SOLAR REFRIGERATOR

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. FABRICATION OF SOLAR REFRIGERATOR GUIDED BY:- SUBMITTED BY:- KIRAN RAJ K RAVI KANT PANDEY DEPARTMENT OF RAVISH KUMAR MECHANICAL ENGG. RAJEEV KUMAR VIKAS KUMAR VIKASH KUMAR SANTOSH ABHISHEK

  2. CONTENTS • OBJECTIVE • INTRODUCTION • CONSTRUCTION PARTS • WORKING OF EQUIPMENTS • POWER CALCULATION • OPERATING SPECIFICATION • ADVANTAGES • LIMITATIONS • APPLICATIONS

  3. OBJECTIVE • To design and develop a thermoelectric refrigerator in order to produce a small quantity of refrigerating effect by using Solar energy. • To effectively use the low grade Solar energy rather than using high grade energy. • To design a refrigerating unit which will work without any moving parts. • To develop a vibration less refrigerator.

  4. INTRODUCTION • Freezing action means transfer of heat from low temperature to a high temperature body • Freezing effect can be produced by vapour compression, vapour absorption, and thermoelectric effect • Solar fridge works on the principle of thermo electric refrigeration • It is non conventional type of refrigeration used to produce small amount of refrigeration • The working principle is based on peltier effect

  5. FIG-1. SOLAR FRIDGE

  6. CONSTRUCTION PARTS • Solar panel • Battery • Thermoelectric device • Air blower

  7. SOLAR PANEL • Solar panel consists of solar photovoltaic cells which converts solar energy into electrical energy • One cell in the panel is capable of producing 0.45v is when current is 0.27A /mm2 • V=(P-Q)(T2-T1) where v=voltage induced,P,Q are photovoltaic coefficient of two voltaic materials T1&T2 are temperatures of two materials

  8. SOLAR CELL

  9. BATTERY • The device consist of lead-acid cell • Sulphuric acid is used as electrolyte • Gives high load current of current rating (100-300) A-hr • The following chemical phenomena takes place • PbO₂ + 2H₂SO₄ 2PbSO₄ + 2H₂O • One cell has nominal output voltage2.1v • Charging can be done to restore o/p voltage

  10. LEAD ACID CELL

  11. THERMOELECTRIC DEVICE • Thermoelectric device are pair of two dissimilar metals, semiconductors or conductor with semiconductor. • The pair should have high electrical conductivity but low thermal conductivity because we are working with low amount of refrigeration. • In this system the device is made of extrinsic semiconductor having p-n junction in series with required no of cells. • The energy difference of conduction band of material should be high for higher refrigeration

  12. THERMOELECTRIC DEVICE

  13. WORKING PRINCIPLE • System works on peltier effect • As d.c supply is provided there is formation of hot and cold junctions • The heat absorbed or expellded is given by QhorQc=B*I=A*T*I • Qh or Qc is heat absorbed or expellded • B is diffrentialpeltiercofficient • I is flowing current in circuit

  14. PELTIER EFFECT

  15. SEMICONDUCTOR MODEL

  16. POWER CALCULATION • Qh = QC + Pin • COP = QC / Pin Where: • Qh = the heat released to the hot side of the thermoelectric (watts).

  17. QC = the heat absorbed from the cold side (watts). • Pin = the electrical input power to the thermoelectric (watts). • COP = coefficient of performance of the thermoelectric device, typically is between 0.4 and 0.7 for single stage applications. • Estimating QC, the heat load in watts absorbed from the cold side is difficult, because all thermal loads in the design must be considered.

  18. By energy balance across the hot and cold junction it produces • Qh= (α Th) x I - C (Th - Tc) + I2 R/2 • QC = (α Tc) x I - C (Th - Tc) - I2 R/2 (17.7) • R = RA + RB • C = (kA+ kB) (A/L)

  19. To get the max the heat absorbed from the cold side (QC); by differentiate the Qc to the electric current I, • d Qc /d I = 0 • Then it produces • Iopt. = α Tc /R   • Substitute for Iopt. In Equation to get the max the heat absorbed from the cold side   • QC (max) = [(Z Tc2)/2 - (Th - Tc)] C Where, Z = Figure of merit for the material A and B = α2 / R C

  20. OPERATING SPECIFICATION Th = 30oC = 303 K Tc = 5oC = 278 K d = 0.1 cm L = 0.125 cm A = (π/4) (0.1)2 =7.854 x 10-3 cm2   Overall electric resistance (R) = Relement + Rjunction= 1.1 Relement = 1.1(ρp + ρn) (L/A)

  21. = 1.1 (0.001 + 0.0008) (0. 125 / 7.854 x 10-3) = 0.0315 Ω • Conduction coefficient (C) = (kp + kn) (A/L) = (0.02 + 0.02) (7.854 x 10-3 /0.125) = 2.513 x 10-3 W/K • Figure of merit (Z) = (αp - αn) 2/ RC = (360 x 10-6)2/ (0.0315 x 2.513 x 10-3) = 1.636 x 10-3 K-1 • Number of couples required.   QC = QC (max) = N C [(Z Tc2)/2 - (Th - Tc)] 10 = N (2.513 x 10-3) [0.5 (1.636 x 10-3 x (278)2) - (25)] N =105couples

  22. Rate of heat rejection to the ambient (Qh) Iopt. = (αp - αn) Tc /R = (360 x 10-6) x 278/ 0.0315 = 3.2 A • Qh= N [(αp - αn) Th x Iopt - C (Th - Tc) + I2opt R/2] = 105 [(360 x 10-6) 303 x 3.2 - 2.513 x 10-3 (25) +(3.2)2 0.0315/2] = 47 W • COP = QC / Pin Pin (Power input by power source to the thermoelectric) = Qh - QC = 47 - 10 = 37 W

  23. COP = 10 / 37 = 0.27 • The voltage drop across the d.c. power source.   voltage drop (∆V) = Pin / I = 37 / 3.2 = 12 volt(approx)

  24. OBSERVATION OF WORKING PARAMETERS • CHANGE IN TEMP Current-3.2amp Voltage-12V 2 4 6 8 10 12 14 16 18 20 22 2 4 6 8 10 12 14 16 18 20 22 TIME

  25. ADVANTAGES • No moving parts, hence operation is noiseless. • Simple and fewer parts are required. • Less power consumption. • Maintenance cost is low. • Easily portable. • Suitable for low capacity. • Compact in size. • The weight per unit refrigeration is considerably lower than conventional refrigeration system.

  26. An interchange of heating and cooling process can be exercised by reversing the polarity. • An important advantage of this refrigeration system is the independence of C.O.P. on the size of thermo-electric refrigerator and this makes it particularly attractive to use peltier cooling when the cooling capacity required is high. • It is free from vibration of any kind unlike the vapour compression refrigeration, which uses compressor making it to vibrate.

  27. LIMITATIONS • Low C.O.P. • Advantageous only for units of smaller capacity. • Can not be used for large freezing requirement. • Unavailability of suitable materials of high figure of merit.

  28. APPLICATION • Peltier refrigerators are widely used in several western countries. • Serum coolers for preservation of blood plasma and serums. • Photo multiplier cooler. • Dew point hygrometer for determining absolute humidity. • Constant low temperature bath and chambers.

  29. CONCLUSION • In this work, a portable thermoelectric generator unit was fabricated and tested for the cooling purpose. The refrigerator was designed based on the principle of a thermoelectric module to create a hot side and cold side. The cold side of the thermoelectric module was utilized for refrigeration purposes whereas the rejected heat from the hot side of the module was eliminated using heat sinks and fans. In order to utilize renewable energy, solar energy was integrated to power the thermoelectric module in order to drive the refrigerator.

  30. Furthermore, the solar thermoelectric refrigerator avoids any unnecessary electrical hazards and provides a very environmentally friendly product. In this regard, the solar thermoelectric refrigerator does not produce chlorofluorocarbon (CFC), which is believed to cause depletion of the atmospheric ozone layer. In addition, there will be no vibration or noise because of the difference in the mechanics of the system. In addition the rejected heat from the solar thermoelectric refrigerator is negligible when compared to the rejected heat from conventional refrigerators. Hence, the solar thermoelectric refrigerator would be less harmful to the environment

  31. THANK YOU

More Related