1 / 12

New documents to clarify the mapping between BPMs, FECs and FIP addresses. (EDMS 1342851 ).

Document : “LHC Orbit System Low level SW procedures” : EDMS ID 1348775 . Contains an introduction to the system infrastructure and several low level procedures: Calculation of the LHC Beam Position in mm: Main difference wrt LHC run#1 are: Update of the coefficients.

inge
Download Presentation

New documents to clarify the mapping between BPMs, FECs and FIP addresses. (EDMS 1342851 ).

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Document : “LHC Orbit System Low level SW procedures” : EDMS ID 1348775. Contains an introduction to the system infrastructure and several low level procedures: • Calculation of the LHC Beam Position in mm: Main difference wrt LHC run#1 are: • Update of the coefficients. • 2D geometrical corrections. Those coefficients can be found in Andriy’s document : EDMS ID 1342295 (Table 2). • No more multiplication by Kf before geom. non-linearity correction. • Tilt expressed as an angle, and not as a cos (45°), to allow generalization to all the BPMs. • QA: SW “embedded” offsets and tilts should be specified on this document. • D. Missiaen will provide us updated info about offsets & tilts by the end of the year. (BPMD, etc). • Temperature compensation: keep as it is implemented now. • Hard-coded • Some errors were found in the FIP decoding for the “FipOverview” procedure described in the previous document version. Application should be checked. • Described procedure to obtain serial numbers of the tunnel cards as human readable numbers.

  2. New documents to clarify the mapping between BPMs, FECs and FIP addresses. (EDMS 1342851). • There will be new BPMs, and some name changes. These changes will be propagated soon to the previous document. • Pt 3 : • Pt 4 : New monitors for the BGI: BPMWI.5L4.B1 and BPMWI.5R4.B2 • Pt6:

  3. Pt 5 : BPMs in Roman Pots will move from 4L6 to 6L5 and from 4R5 to 6R5. 6L5 and 6R5 already had Totem stations. New names to be defined. • Channels equipped with Diode Orbit also seen by the OFC: • Duplicated channels for BPMS in Q1. • Collimator BPMs.

  4. Terminals in the SR buildings? Before LS1, PC in rack BY01. • Either we find a new place to install them back • There are empty racks in the same row: SR1, SR2, SR5, SR6. • SX4 we can place it in a table in the BI closed local. • SR8: empty racks • Without place: SR3, SR7 and SR8. • 2) Either we replace them by CO centrally managed PC + 1U KVM console installed in a free slot at rack BY05. • CO accepts this solution and seems easy to integrate. • Prices from 700CHF up to 2k CHF, and typically ~1400CHF.

  5. Some KVM consoles: • StartTech.com : starting at ~760 USD (17” 1280x1024 display, 1 VGA and 1 USB A) up to 1400 USD (17” 1920x1080 display, 1 USB B, 1 VGA and 2 PS/2). • Dell: ref. 331-9437 for 1240 USD (18.5" display, and 1 KVM and 2xUSB interfaces). • APC: 17” or 19”, comes with a custom cable at the console end and it has 2 PS/2 + 1 VGA at the other end. • Tripp lite: 17” 1280x1024 LCD with also a KVM cable kit (VGA + 2 PS/2). 2kCHF at mouser.ch • Schroff: 17” 1280x1024, 2 PS/2 or USB, about 1200 euro/piece.

  6. SR1 2 empty racks

  7. SR2 2 empty racks

  8. SR3 Local ? Drawing is wrong ! No rack empty but these two have many space available.

  9. SE5 2 empty racks

  10. SR6 Empty rack

  11. SR7 Many space available, but magnet interlock.

  12. SR8 Empty racks EPC local ?

More Related