1 / 41

Chapter 2 AC to DC CONVERSION (RECTIFIER)

Chapter 2 AC to DC CONVERSION (RECTIFIER) Single-phase, half wave rectifier Uncontrolled: R load, R-L load, R-C load Controlled Free wheeling diode Single-phase, full wave rectifier Uncontrolled: R load, R-L load, Controlled Continuous and discontinuous current mode

Antony
Download Presentation

Chapter 2 AC to DC CONVERSION (RECTIFIER)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Chapter 2AC to DC CONVERSION (RECTIFIER) • Single-phase, half wave rectifier • Uncontrolled: R load, R-L load, R-C load • Controlled • Free wheeling diode • Single-phase, full wave rectifier • Uncontrolled: R load, R-L load, • Controlled • Continuous and discontinuous current mode • Three-phase rectifier • uncontrolled • controlled Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  2. AC input DC output Rectifiers • DEFINITION: Converting AC (from mains or other AC source) to DC power by using power diodes or by controlling the firing angles of thyristors/controllable switches. • Basic block diagram • Input can be single or multi-phase (e.g. 3-phase). • Output can be made fixed or variable • Applications: DC welder, DC motor drive, Battery charger,DC power supply, HVDC Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  3. + vs _ + vo _ w t vs p 2p vo io Single-phase, half-wave, R-load Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  4. i + vR _ + vo _ + vs _ + vL _ Half-wave with R-L load Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  5. R-L load Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  6. vs, io b w t vo vR vL 2p 0 4p p 3p R-L waveform Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  7. Extinction angle Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  8. RMS current, Power Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  9. Vm + vs _ iD + vo _ vs Vo 2p 3p 3p /2 4p D p /2 p vo Vmax Vmin iD Half wave rectifier, R-C Load a q Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  10. Let C initially uncharged. Circuit is energised at wt=0 Diode becomes forward biased as the source become positive When diode is ON the output is the same as source voltage. C charges until Vm After wt=p/2, C discharges into load (R). The source becomes less than the output voltage Diode reverse biased; isolating the load from source. The output voltage decays exponentially. Operation Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  11. Estimation of q Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  12. Estimation of a Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  13. Ripple Voltage Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  14. Capacitor Current Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  15. Peak Diode Current Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  16. Vm vs Vo 2p 3p 3p /2 4p D p /2 p vo Vmax Vmin iD a q Example A half-wave rectifier has a 120V rms source at 60Hz. The load is =500 Ohm, C=100uF. Assume a and q are calculated as 48 and 93 degrees respectively. Determine (a) Expression for output voltage (b) peak-to peak ripple (c) capacitor current (d) peak diode current. Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  17. Example (cont’) Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  18. ig v ia s + vs _ w w w t t t vo v i g a Controlled half-wave + vo _ Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  19. i + vR _ + vo _ + vs _ w + vL _ t vs p 2p vo io b a Controlled h/w, R-L load Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  20. Controlled R-L load Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  21. Examples • A half wave rectifier has a source of 120V RMS at 60Hz. R=20 ohm, L=0.04H, and the delay angle is 45 degrees. Determine: (a) the expression for i(wt), (b) average current, (c) the power absorbed by the load. 2. Design a circuit to produce an average voltage of 40V across a 100 ohm load from a 120V RMS, 60Hz supply. Determine the power factor absorbed by the resistance. Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  22. + vR _ + vL _ io + vo _ + vs _ io io vo= 0 + vo _ vo= vs + vs _ + vo _ io D2 is on, D1 is off D1 is on, D2 is off Freewheeling diode (FWD) • Note that for single-phase, half wave rectifier with R-L load, the load (output) current is NOT continuos. • A FWD (sometimes known as commutation diode) can be placed as shown below to make it continuos Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  23. Operation of FWD • Note that both D1 and D2 cannot be turned on at the same time. • For a positive cycle voltage source, • D1 is on, D2 is off • The equivalent circuit is shown in Figure (b) • The voltage across the R-L load is the same as the source voltage. • For a negative cycle voltage source, • D1 is off, D2 is on • The equivalent circuit is shown in Figure (c) • The voltage across the R-L load is zero. • However, the inductor contains energy from positive cycle. The load current still circulates through the R-L path. • But in contrast with the normal half wave rectifier, the circuit in Figure (c) does not consist of supply voltage in its loop. • Hence the “negative part” of vo as shown in the normal half-wave disappear. Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  24. output vo io iD1 Diode current iD2 t w 0 2p 3p p 4p FWD- Continuous load current • The inclusion of FWD results in continuos load current, as shown below. • Note also the output voltage has no negative part. Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  25. D1 D3 is is iD2 iD1 iD1 io + vs _ + vo _ D4 Full Bridge D2 D1 + vs1 _ + vD1 - + vs _ - vo + + vs2 _ io + vD2 - D2 Center-tapped Full wave rectifier • Center-tapped (CT) rectifier requires center-tap transformer. Full Bridge (FB) does not. • CT: 2 diodes • FB: 4 diodes. Hence, CT experienced only one diode volt-drop per half-cycle • Conduction losses for CT is half. • Diodes ratings for CT is twice than FB Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  26. D1 D3 is iD1 io + vs _ + vo _ D4 Full Bridge D2 Vm vs 4p 3p 2p p Vm vo vD1 vD2 -Vm vD3 vD4 -Vm io iD1 iD2 iD3 iD4 is Bridge waveforms Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  27. is iD1 iD2 Vm vs D1 4p + vs1 _ 3p + vD1 - 2p p Vm + vs _ - vo + vo + vs2 _ io vD1 + vD2 - -2Vm D2 Center-tapped vD2 -2Vm io iD1 iD2 is Center-tapped waveforms Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  28. io is iD1 + vR _ + vo _ + vs _ w t + vL _ vs p 2p iD1 , iD2 iD3 ,iD4 io vo is Full wave bridge, R-L load Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  29. Approximation with large L Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  30. vs w t p 2p io iD1 , iD2 vo iD3 ,iD4 is R-L load approximation Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  31. Examples Given a bridge rectifier has an AC source Vm=100V at 50Hz, and R-L load with R=100ohm, L=10mH • determine the average current in the load • determine the first two higher order harmonics of the load current • determine the power absorbed by the load Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  32. is T1 iD1 io T3 + vs _ + vo _ T2 T4 Controlled full wave, R load Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  33. io is iD1 + vR _ + vo _ + vs _ + vL _ io b p a 2p +a p vo Discontinuous mode p+a io b p 2p a vo Continuous mode Controlled, R-L load Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  34. Discontinuous mode Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  35. Continuous mode Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  36. D1 io D3 vp + vs _ + vo _ D4 vn D2 vo =vp -vn Single-phase diode groups • In the top group (D1, D3), the cathodes (-) of the two diodes are at a common potential. Therefore, the diode with its anode (+) at the highest potential will conduct (carry) id. • For example, when vs is ( +), D1 conducts id and D3 reverses (by taking loop around vs, D1 and D3). When vs is (-), D3 conducts, D1 reverses. • In the bottom group, the anodes of the two diodes are at common potential. Therefore the diode with its cathode at the lowest potential conducts id. • For example, when vs (+), D2 carry id. D4 reverses. When vs is (-), D4 carry id. D2 reverses. Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  37. Vm Vm van vbn vcn vp vn vo =vp - vn 3p 4p p 2p 0 Three-phase rectifiers D1 io + van - D3 D5 vpn + vbn - n + vo _ D2 + vcn - vo =vp -vn vnn D6 D4 Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  38. Three-phase waveforms • Top group: diode with its anode at the highest potential will conduct. The other two will be reversed. • Bottom group: diode with the its cathode at the lowest potential will conduct. The other two will be reversed. • For example, if D1 (of the top group) conducts, vp is connected to van.. If D6 (of the bottom group) conducts, vn connects to vbn . All other diodes are off. • The resulting output waveform is given as: vo=vp-vn • For peak of the output voltage is equal to the peak of the line to line voltage vab . Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  39. vo vo p/3 Vm, L-L 0 2p/3 p/3 Three-phase, average voltage Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  40. io Vm + van - T3 T5 vpn + vbn - n + vo _ T2 + vcn - vnn T6 T4 Controlled, three-phase T1 a vbn van vcn vo Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

  41. Output voltage of controlled three phase rectifier • EXAMPLE: A three-phase controlled rectifier has an input voltage of 415V RMS at 50Hz. The load R=10 ohm. Determine the delay angle required to produce current of 50A. Power Electronics and Drives (Version 3-2003), Dr. Zainal Salam, 2003

More Related