1 / 15

Choose Your Motor Type (Click The Appropriate Picture)

Choose Your Motor Type (Click The Appropriate Picture). S-Can. Slimline- FF050. Topic Jump. Choose Your Pod Configuration (Click The Appropriate Picture). Inline. Sidewinder. Topic Jump. Choose Your Pod Configuration (Click The Appropriate Picture). Inline. “Super Slimline”.

alissa
Download Presentation

Choose Your Motor Type (Click The Appropriate Picture)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Choose Your Motor Type(Click The Appropriate Picture) S-Can Slimline- FF050 Topic Jump

  2. Choose Your Pod Configuration (Click The Appropriate Picture) Inline Sidewinder Topic Jump

  3. Choose Your Pod Configuration (Click The Appropriate Picture) Inline “Super Slimline” Topic Jump

  4. Magnet Installation (Optional) 1. Insert the magnet into one side of the magnet recess. Make sure the top edge of the magnet is below the hold down tab. 2. Apply firm but gentle pressure to the opposite side of the magnet until it drops below the hold down tab. 3. When viewed from the bottom of the pod, the magnet surfaces should be flush (or VERY close) to the bottom pod surface Topic Jump NEXT STEP

  5. Magnet Installation (Optional) 1. Insert the magnet into one side of the magnet recess. Make sure the top edge of the magnet is below the hold down tab. 2. Apply firm but gentle pressure to the opposite side of the magnet until it drops below the hold down tab. 3. When viewed from the bottom of the pod, the magnet surfaces should be flush (or VERY close) to the bottom pod surface Topic Jump NEXT STEP

  6. Magnet Installation (Optional) 1. Insert the magnet into one side of the magnet recess. Make sure the top edge of the magnet is below the hold down tab. 2. Apply firm but gentle pressure to the opposite side of the magnet until it drops below the hold down tab. 3. When viewed from the bottom of the pod, the magnet surfaces should be flush (or VERY close) to the bottom pod surface Topic Jump NEXT STEP

  7. S Can Motor Installation 1. Insert the endbell side of the motor into the rear bulkhead as shown. Ensure to push the motor far enough toward the back of the pod to clear the front bulkhead. 2. Apply firm but gentle pressure to the top of the front side of the motor until it snaps into place. NOTE: First installation will feel tight. This is on purpose to prevent motor rotation. 3. When viewed from the side, the motor surfaces should be flush (or VERY close) to the bottom pod surface. Make sure the front of the motor is fully seated if you find the motor is not flush. Topic Jump NEXT STEP

  8. Slimline Motor Installation 1. Insert the endbell side of the motor into the front bulkhead as shown. Ensure to align the endbell cap into the hole on the bulkhead. Make sure the motor is rotated so that the tabs clear the bulkhead. 2. Apply firm but gentle pressure to the top of the shaft side of the motor until it snaps into place. NOTE: First installation will feel tight. This is on purpose to prevent motor rotation. 3. When viewed from the side of the pod, the motor WILL BE AT AN ANGLE to the bottom pod surface. This is NORMAL. Make sure the shaft side of the motor is fully seated in the rear bulkhead. Topic Jump NEXT STEP

  9. Choose Your Bushing Configuration(Click The Appropriate Picture) Snap Bushings Insert Bushings Topic Jump

  10. Snap Bushing Installation NOTE:DO NOT INSTALL BUSHINGS ON AXLE BEFORE INSTALLING INTO MOTOR POD!!!This can cause bushing misalignment and break the snap supports. 1. Install snap bushings one at a time. Install each snap bushing by gently pressing it into place with your fingers. 2. Align the bushings by installing the axle. Push the axle through one bushing and then to the next. If it doesn’t go in easily, simply wiggle the axle a bit until it goes through. 3. If the axle does not spin freely, remove the axle, then the bushings, and lightly sand or file the area indicated. Repeat steps 1-3 until the axle will easily drop through the bushings. A drop of super glue on each bushing should be adequate to hold the bushings permanently if desired. Topic Jump NEXT STEP

  11. Insert Bushing Installation 1. Install each insert bushing by gently pressing it into place with your fingers. 2. Align the bushings by installing the axle. Push the axle through one bushing and then to the next. If it doesn’t go in easily, simply wiggle the axle a bit until it goes through. NOTE: Sometimes it helps to leave a small gap between the bushing and the motor pod surface to allow some movement. 3. Once the axle is through both bushings and they are snug in their holders, set the pod on a flat surface such as a table top, and gently push down on both ends of the axle nearest the carrier. This should align the bushings so that the axle drops through them without hesitation. Topic Jump NEXT STEP

  12. Insert Bushing Installation- Continued 4. If the axle does not drop through both bushings simultaneously, simply wiggle each end of the axle slightly to better align the bushings. 5. Once the axle falls through both bushings easily, add a drop of superglue to each bushing where it meets the carrier. Once the glue has set, make sure the axle spins freely once installed. 6. Remove the axle and apply glue to the inside of the bushing holder area making sure not to get glue inside the bushing itself. Topic Jump NEXT STEP

  13. Final Assembly Simply add your selected gears, wheels and tires and it is ready for installation in a chassis. GO FAST! Enjoy : ) Topic Jump

  14. Topic Selection Restart Tutorial Magnet Installation S- Can Motor Installation Slimline Motor Installation Snap Bushing Installation Insert Bushing Installation Final Assembly

  15. Magnet Installation (Optional) 1. Insert the magnet into one side of the magnet recess. Make sure the top edge of the magnet is below the hold down tab. 2. Apply firm but gentle pressure to the opposite side of the magnet until it drops below the hold down tab. 3. When viewed from the bottom of the pod, the magnet surfaces should be flush (or VERY close) to the bottom pod surface Topic Jump

More Related