1 / 22

Building the 5.5 HP Tecumseh

Building the 5.5 HP Tecumseh. Intake Manifold, Carburetor, Muffler, Heat Shield, Flywheel Cover . What are the 4 steps of combustion?. 1. INTAKE 2. COMPRESSION 3. SPARK 4. EXHAUST. The 4 Steps of Combustion. Crankshaft. Intake M anifold. What does the Intake Manifold do??.

artan
Download Presentation

Building the 5.5 HP Tecumseh

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Building the 5.5 HP Tecumseh Intake Manifold, Carburetor, Muffler, Heat Shield, Flywheel Cover.

  2. What are the 4 steps of combustion? • 1. INTAKE • 2. COMPRESSION • 3. SPARK • 4. EXHAUST

  3. The 4 Steps of Combustion

  4. Crankshaft

  5. Intake Manifold

  6. What does the Intake Manifold do?? • The Intake Manifold brings in the Air AND Fuel to the cylinder heads. • The Carburetor bolts right on top of the intake manifold.

  7. Carburetor

  8. What does the Carburetor do?? • The Carburetor brings fuel into the engine. • The throttle (gas pedal) is connected to the carburetor. • This tells the carburetor how much fuel to allow into the engine.

  9. STARTING THE BUILD!

  10. Add The Intake Manifold • Make sure to screw it in with your HAND before tightening with a SCREW DRIVER! • DON’T FORGET THE GASKET!

  11. Carburetor • Line up the Carburetor with gasket and align over holes. • Use a screwdriver and wrench to tighten down the carburetor. • DON’T OVER TIGHTEN!

  12. Muffler • 1. Align the two muffler bolts through the muffler. • 2. Tighten the muffler bolts. • What does this part do??

  13. Throttle Linkage • 1. Attach the linkage pin to the throttle. (Red Arrow!) • 2. Place the linkage pin in the groove on the top of the Carburetor. (Green Arrow!)

  14. Secure the Throttle Linkage • 1. Align the Throttle Linkage over the top of the Camshaft pin. WITH YOUR HANDS! • 2. Make sure there Camshaft pin looks like the picture!! • 3. Tighten down the tension bolt until snug.

  15. Attach the Heat Shield • Attach and connect the bolts for the heat shield. • Don’t forget to re-attach the spark plug!

  16. Connect The Power Wires • Connect the Ground Wire (BLACK) to the middle terminal. • Connect the Oil Pressure Wire (BLUE) to the top terminal. • Connect the Power Wire (GREEN) to the bottom terminal.

  17. Flywheel Cover • Align the flywheel cover and attach it using the bolts required.

  18. Flywheel Cover • Align the flywheel cover and attach it using the bolts required.

  19. Governor and Spring • Attach the Governor Plate to the flywheel cover. • Attach the governor spring to the bottom of the throttle linkage.

  20. Air Cleaner • Attach the Air Cleaner to the engine and align over the rod. • Gentle tighten the air cleaner with your hand until snug.

  21. The 4 Steps of Combustion

  22. HI FIVE! • GREAT TEAMWORK SO FAR ON THE BUILD! Crankcase!! Cylinder Head!! Ignition!!! AIR & FUEL SYSTEM!!!

More Related