1 / 23

Engine Terminology

Engine Terminology. Engine Lubrication Principles Engine Oils Lesson 1. Engine Doc – S. Ruch 2008. Agenda. Primary function Lubrication principles Hydrodynamic action Engine oils Ratings. Primary Function. Separate moving components. Lubrication Principles. Hydrodynamic Lubrication

clare
Download Presentation

Engine Terminology

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Engine Terminology Engine Lubrication Principles Engine Oils Lesson 1 Engine Doc – S. Ruch 2008

  2. Agenda • Primary function • Lubrication principles • Hydrodynamic action • Engine oils • Ratings

  3. Primary Function • Separate moving components

  4. Lubrication Principles Hydrodynamic Lubrication Hydro - liquids - as in hydraulics - engine oil Dynamic - motion - engine parts in relative motion

  5. Hydrodynamic Lubrication • is the wedge shape of oil film that completely separates two surfaces that have relative motion Do you remember the name for engine bearings?

  6. Anti-Friction Bearings

  7. Hydrodynamic Lubrication • occurs between the shaft journals and the bearing inserts. YouTube - SPH BEARING FLOW

  8. Hydrodynamic Lubrication • The engine lubrication system must provide a constant supply of clean oil at a high enough pressures to force oil to the bearings to allow enough flow for cooling of the bearing surfaces • The oil is supplied to the lightly loaded area of the bearing and then the hydrodynamic process takes over • The hydrodynamic oil film pressures developed on the engine bearing surfaces may exceed 1000 psi. • Loss of oil supply will result in bearing failure

  9. Hydrodynamic Lubrication • Normal bearing wear happens when there is a lack of hydrodynamic lubrication. • This occurs when? Initial engine start up • When the engine is off, the crankshaft pushes most of the oil from around it as it settles to the bottom of the bearings.

  10. Boundary Lubrication • Occurs when the oil film is extremely thin and the high spots of the surfaces touch

  11. Engine Oils Purpose • Lubricate all moving parts to prevent wear • Reduce friction • Aid in cooling the engine • Assist the cylinder seal at the piston rings • Neutralize acids formed from combustion process • Prevent rust and corrosion • Clean the engine and hold dirt in suspension

  12. Oil Viscosity • Viscosity is the resistance to flow of an oil • A high viscosity oil has a greater resistance to flow and is said to be thicker than a lower viscosity oil • As an oil cools it thickens and as it heats up it thins out. • Viscosity changes with temperature

  13. Oil Viscosity • Oil must not be too thick at low temperatures or cranking speeds will be low, and hard or no starts will result, due to the increased co-efficient of friction. • Oil must not be too thin at high temperatures or the oil film will not support the loads placed on it and boundary lubrication will occur and increase the co-efficient of friction. • Viscosity is measured by the Say bolt UniversalViscosity Test which measures the number of seconds for a definite quantity of oil to flow through a fixed orifice into a measured container at a specified temperature.

  14. Viscosity Index Improver • Polymer additive that induces thickening of a thin base oil at high temperatures • 10W30 oil starts as a 10W oil and viscosity index improvers are added in sufficient quantity to bring the hightemperature viscosity rating up to the S.A.E. 30 standard. • VI improvers make up between 6 and 15% of the oil • VI improvers breakdown with use • Oil oxidizes and thickens forming sludge YouTube - oil aditives

  15. These oils were chilled to -35C for 16 hours. The photo was taken 30 seconds after the caps were removed from the containers. YouTube - Tech Talk on Engine Oil - with Castrol

  16. S.A.E. Oil Viscosity Ratings • Grade number represents the viscosity range of an oil • A grade number with no letter following means that oil was tested only at 100C (212F) eg. SAE 10, 20 30 • The higher the number the higher the viscosity • Grade numbers that are followed by a the letter “W” indicate that the oil was tested at -18C (0F) and are given a viscosity rating at that temperature. eg. 10W, 20W • Multigrade oils like 10W30 are tested at -18C and 100C and meet the S.A.E. specifications for those temperatures (VI improvers are added to meet these specifications)

  17. A.P.I. Ratings - Oil Quality American Petroleum Institute • Letter Ratings that are applied to oils tested for quality Gasoline engine ratings • “S” means Service (spark ignition) • Ratings from SA (straight mineral oil) to SL. • SL is the highest rated oil starting in 2001. • Use the highest rated oil available (or as specified)

  18. A.P.I. Ratings - Oil Quality Diesel engine ratings • “C” means Commercial (compression ignition) • Ratings from CA (obsolete) to CG4 which is for severe duty high speed four stroke diesel engines. • Always use the correct oil for the application

  19. ILSAC Oil Rating International Lubricant Standardization and Approval Committee • Combination of SAE Viscosity and API Quality ratings • GF1 - pre 1996 • GF2 - 1997 to 1999 • GF3 - 2000 • Starburst Symbol

  20. Synthetic Oils Base Stocks not from crude oil Polyalphaolefins - Mobil 1 Organic esters - alcohol and acid - Castrol Syntec Polygycols - polyalkaline gylcol (PAG oil for 134a A/C) Advantages • remains fluid at very low temperatures • lower internal friction - fuel economy and cooler engine • resists oxidation Disadvantages • $ cost $ - 4 to 5 times more money • may not be compatible - gaskets, seals = oil leaks

More Related