1 / 25

River Sediment Calibration Rules

River Sediment Calibration Rules. Gary Shenk 5/3/05 Modeling Subcommittee. Schedule. Sediment calibration must be done by June 1. Nutrient Calibration must be done by August 1. Refinements will follow over the next 18 months. Calibration Method. Flow

deo
Download Presentation

River Sediment Calibration Rules

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. River Sediment Calibration Rules Gary Shenk 5/3/05 Modeling Subcommittee

  2. Schedule • Sediment calibration must be done by June 1. • Nutrient Calibration must be done by August 1. • Refinements will follow over the next 18 months.

  3. Calibration Method • Flow • Automatic calibration method developed • Edge-of-Field Sediment • Automatic calibration method developed • River Sediment • Two out of three ain’t bad • Developed calibration rules and will apply them by hand

  4. Outflow Inflow Deposition Scour River Cohesive Sediment Simulation Suspended Sediment Bed Storage (unlimited)

  5. Deposition River Sediment Simulation Bed Storage (unlimited)

  6. Scour River Sediment Simulation Bed Storage (unlimited)

  7. River Sand Simulation Adjustments are then made to the bed depth

  8. All rivers segments upstream of a calibration point have identical parameters For nested rivers, this applies only to rivers downstream of any upstream gages. Remington Robinson Rappahannock Calibration Rules 1

  9. Uncalibrated

  10. Stau 97 percentile Ctau 93 SW .001 inches/sec CW .0001 CM = 1 lb/ft^2/day SM = 1 KS = .003 empirical ES = 4 High flow in the ballpark, but low flow is a problem. Lowest concentrations are mostly VSS, which is not yet simulated and are at LOD in the observed

  11. Stau 97 Ctau 93 SW .001 CW .0001 CM = 1 SM = 1 KS = 3 ES = 3 To deal with the lack of VSS in the simulation, use SAND to make the low concentrations work out. This can be easily reversed when VSS are simulated

  12. Stau 99 Ctau 96 SW .001 CW .0001 CM = 1 SM = 1 KS = 3 ES = 3 Reduce the frequency of scour to deal with over-simulation

  13. Stau 99 Ctau 96 SW .001 CW .0001 CM = .5 SM = .5 KS = 3 ES = 3 Reduce the effect of scour to deal with over-simulation

  14. Stau 99.5 Ctau 98 SW .001 CW .0001 CM = .5 SM = .5 KS = 2.8 ES = 3 Tighten up the simulation

  15. Issues with simulation • Low values dominate the CFD, but they are not meaningful from: • A load standpoint • An accuracy of observation standpoint • Simulation standpoint (no VSS) • Flow not perfectly calibrated • If peak is missed by a day, then the concentration simulation should not match the observed.

  16. If simulated or observed value is below 10 mg/l set it to 10 mg/l. Check simulation for 24 hours before and after observation and set simulated value to point closest to observation. ‘Windowed’ comparison Of the highest observed and simulated peaks at all calibration stations, almost as many peaks occurred one day apart, but few occurred on two days apart One day apart – 83% of the same day figure Two days apart – 19% of the same day figure

  17. Reported Error I

  18. Stau 97 Ctau 93 SW .001 CW .0001 CM = 1 SM = 1 KS = .003 ES = 4 Starting point

  19. Stau 97 Ctau 93 SW .001 CW .0001 CM = 1 SM = 1 KS = 3 ES = 3 Sand Calibration

  20. Stau 99 Ctau 96 SW .001 CW .0001 CM = 1 SM = 1 KS = 3 ES = 3 Reduce Frequency of Scour

  21. Stau 99 Ctau 96 SW .001 CW .0001 CM = .5 SM = .5 KS = 3 ES = 3 Reduce effect of scour

  22. Stau 99.5 Ctau 98 SW .001 CW .0001 CM = .5 SM = .5 KS = 2.8 ES = 3 Tighten up calibration

  23. Hope for automation • Separate out sections of the CFD • Low part: sand - VSS • Highest part: silt • Mid-high part: clay • PEST • Few parameters • Short run time ~ 1-2 minutes

  24. Plan • Following calibration rules, team will calibrate all stations this month. • Jing Wu – Susquehanna • Jason Pope – Southern Rivers • ICPRB – Potomac • Set up nutrient calibration • Jeff Raffensperger – observed data and input • Gary Shenk – model simulation setup • CBP nutrient team – nutrient input data

More Related