170 likes | 194 Views
Installation Guide for AC-1000RF & SA V1.6. Version Eng1.10 Jul.,25.2012. Union Community Co., Ltd. P - 3 P - 2 P - 1. P - 8 P - 7 P - 6 P - 5 P - 4 P - 3 P - 2 P - 1. 1. External Connectors. Wiegand, RS232 & RS485 Interface. DC Power Input Interface. Data2 (Brown) - 1
E N D
Installation Guide for AC-1000RF & SA V1.6 Version Eng1.10 Jul.,25.2012 Union Community Co., Ltd.
P - 3 P - 2 P - 1 P - 8 P - 7 P - 6 P - 5 P - 4 P - 3 P - 2 P - 1 1. External Connectors Wiegand, RS232 & RS485 Interface DC Power Input Interface Data2 (Brown) - 1 Data3 (Red) - 2 Ground (Black) - 3 Wiegand In Data0 (Orange) - 1 Data1 (Yellow) - 2 Ground (Black) - 3 Wiegand Out FGND (Green) - 3 Ground (Black) - 2 +12~+24V (Red) - 1 RS485A (Green) - 1 RS485B (Blue) - 2 Ground (Black) - 3 RS485 ** PIN 1 is N.C RS232_TXD (Violet) - 2 RS232_RXD (Gray) - 3 RS232_GND (Black) - 4 RS232 TCP/IP NetworkInterface(RJ45) Door Lock & Status Input Interface Ground (Black) - 8 Door_Monitor2 (Blue) - 7 Door_Monitor1 (Green) - 6 Door_Monitor0 (Yellow) - 5 Inside_Open (Orange) - 4 Lock Ground (Black) - 3 Door Lock2 (Red) - 2 Door Lock1 (Brown) - 1
2. Main board feature J120 : RS232 J102 : Wiegand Out J201 : DC Input J301 : LAN Interface SW120 : RS-485 termination resistorON/OFF F201 : Fuse J121 : RS-485 Interface J101 : Wiegand In J151 : Lock Interface SW101: RS232 (TTL/232 level select) Lock Type Select S/W Volume Control Lock Type Select S/W
Special. HiD Module to Wiegand Input interface Wiegand In (J101) Ground (Black) - 3 Data3 (Red) - 2 Data2 (Brown) - 1 Green White Black GND (Black) - 4 NC - 3 NC - 2 5V Vcc (Red) - 1 RED RS232 Debug (J120) * 1 .Insert into the Harness side prior to soldering with 5pcs ready for contraction tube 3pie 10mm. 2 . Connecting with soldering to match the colors as shown in the figure. (Black is connected as Wire 3 ) 3 . The column to shrink to fit the soldering site of contraction Tube after soldering . 4 . Short does not occur to the part to remove the Wire the rest of the iClass, deleted I Taping processing so as not . 5 . When you are finished , open the case of AC1000, to be inserted in each of J101, J120 of Page 3. 6 . After connecting the power Close the Case, you can adjust the settings in the configuration Wiegand IN . * To use the RS232 Cable of Page2, and minus the Violet of Pin 2 When installed toward the Pin1, it is possible to use as a power source . By replacing the orange line in the figure above It is possible to use . * It can be used together HiD Card and Card of the existing AC1000 , the thickness of the product is on Pre-installation check is necessary because it may affect the distance iClass
ON NC Strike 1 2 3 4 5 6 NO/Motor Motor SW153 SW152 Strike/MT Strike/MT AutoDoor AutoDoor SW154 SW151 4. Connecting Dead-Bolt Type Door Lock ( Fail Safe ) 4. 1. Connect with one system & one lock ◈ Lock Type Select Switch 1) SW2 2) SW151~SW154 (-)Black (+)Red - C + ON WnP 1 2 3 4 Door Monitor ◈ Wiring diagram Lock(+) Pin 1 Door Lock1 Door Lock2 Lock Ground Inside_Open Door_Monitor0 Door_Monitor1 Door_Monitor2 Ground (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 Ground (-) Pin 3 Pin 4 Pin 5 Lock(-) Pin 8 Inside Door Open S/W
ON ON NC NC Strike Strike 1 1 2 2 3 3 4 4 5 5 6 6 NO/Motor NO/Motor Motor Motor SW153 SW153 SW152 SW152 Strike/MT Strike/MT Strike/MT Strike/MT AutoDoor AutoDoor AutoDoor AutoDoor SW154 SW154 SW151 SW151 4. Connecting Dead-Bolt Type Door Lock ( Fail Safe ) 4. 2. Connect with two system & one lock ◈ Lock Type Select Switch (-)Black System 1 System 2 (+)Red 1) SW2 2) SW151~SW154 1) SW2 2) SW151~SW154 - C + ON WnP 1 2 3 4 ◈ Wiring diagram Lock (-) Door Monitor Lock (+) Pin3 Pin1 Pin5 Pin1 Pin5 Pin2 Pin8 (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 System 2 System 1
ON NC Strike 1 2 3 4 5 6 NO/Motor Motor SW153 SW152 Strike/MT Strike/MT AutoDoor AutoDoor SW154 SW151 5. Connecting Strike Type Door Lock ( Fail Safe ) 5. 1. Connect with one system & one lock ◈ Lock Type Select Switch 1) SW2 2) SW151~SW154 (-)Black (+)Red Door Monitor ◈ Wiring diagram Lock(+) Pin1 Door Lock1 Door Lock2 Lock Ground Inside_Open Door_Monitor0 Door_Monitor1 Door_Monitor2 Ground (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 Ground Pin 3 Pin 4 Pin 5 Lock(-) Pin 8 Inside Door Open S/W
ON ON NC NC Strike Strike 1 1 2 2 3 3 4 4 5 5 6 6 NO/Motor NO/Motor Motor Motor SW153 SW153 SW152 SW152 Strike/MT Strike/MT Strike/MT Strike/MT AutoDoor AutoDoor AutoDoor AutoDoor SW154 SW154 SW151 SW151 5. Connecting Strike Type Door Lock ( Fail Safe ) 5. 2. Connect with two system & one lock ◈ Lock Type Select Switch System 1 System 2 1) SW2 2) SW151~SW154 1) SW2 2) SW151~SW154 ◈ Wiring diagram Lock (-) Door Monitor Lock (+) Pin1 Pin3 Pin8 Pin5 Pin1 Pin2 Pin5 Pin3 (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 System 2 System 1
ON NC Strike 1 2 3 4 5 6 NO/Motor Motor SW153 SW152 Strike/MT Strike/MT AutoDoor AutoDoor SW154 SW151 6. Connecting Strike Type Door Lock ( Fail Secure ) 6. 1. Connect with one system & one lock ◈ Lock Type Select Switch 1) SW2 2) SW151~SW154 (-)Black (+)Red Door Monitor ◈ Wiring diagram Lock(+) Pin1 Door Lock1 Door Lock2 Lock Ground Inside_Open Door_Monitor0 Door_Monitor1 Door_Monitor2 Ground (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 Ground Pin 3 Pin 4 Pin 5 Lock(-) Pin 8 Inside Door Open S/W
ON ON NC NC Strike Strike 1 1 2 2 3 3 4 4 5 5 6 6 NO/Motor NO/Motor Motor Motor SW153 SW153 SW152 SW152 Strike/MT Strike/MT Strike/MT Strike/MT AutoDoor AutoDoor AutoDoor AutoDoor SW154 SW154 SW151 SW151 6. Connecting Strike Type Door Lock ( Fail Secure ) 6. 2. Connect with two system & one lock ◈ Lock Type Select Switch System 1 System 2 1) SW2 2) SW151~SW154 1) SW2 2) SW151~SW154 ◈ Wiring diagram Lock (-) Door Monitor Lock (+) Pin1 Pin3 Pin5 Pin1 Pin5 Pin3 (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 System 2 System 1
NC Strike ON NO/Motor Motor SW153 SW152 Strike/MT Strike/MT 1 2 3 4 5 6 AutoDoor AutoDoor SW154 SW151 7. Connecting EM Type Door Lock( Fail Safe ) 7. 1. Connect with one system & one lock ◈ Lock Type Select Switch 1) SW2 2) SW151~SW154 Brown (+) Door Monitor ◈ Wiring diagram Lock(+) Pin 1 Pin 1 Door Lock1 Door Lock2 Lock Ground Inside_Open Door_Monitor0 Door_Monitor1 Door_Monitor2 Ground (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 Lock(-) Ground Pin 3 Lock(+) Pin 4 Inside_Open Pin 5 Pin 8 Inside Door Open S/W
2) SW151~SW154 NC Strike ON NO/Motor Motor SW153 SW152 Strike/MT Strike/MT 1 2 3 4 5 6 AutoDoor AutoDoor SW154 SW151 7. Connecting EM Type Door Lock( Fail Safe ) 7. 2. Connect with one system & two lock ** Use external DC Power Adapter ◈ Lock Type Select Switch Lock 1 1) SW2 - (Black) ◈ Wiring diagram + (Red) (-) Lock(-) 12V 3A Adapter Lock(+) (+) Exit B Door Monitor Input1 GND Pin2 Pin1 Pin4 Pin5 Pin8 (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 Inside Door Open S/W Lock 2
NC Strike ON NO/Motor Motor SW153 SW152 Strike/MT Strike/MT 1 2 3 4 5 6 AutoDoor AutoDoor SW154 SW151 Inside Door Open S/W 8. Connecting Auto Door ( Contact Control ) 8. 1. Connect with two system & one door ◈ Lock Type Select Switch 1) SW2 2) SW151~SW154 Auto Door Motor Auto Door Operating Part Auto-Door Sensor Auto-Door Monitor Sensor Input Line 9P CONN ◈ Wiring diagram Lock 1 Pin 1 Door Lock1 Door Lock2 Lock Ground Inside_Open Door_Monitor0 Door_Monitor1 Door_Monitor2 Ground (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 Lock 2 Pin 2 Lock(+)
ON ON NC NC Strike Strike 1 1 2 2 3 3 4 4 5 5 6 6 NO/Motor NO/Motor Motor Motor SW153 SW153 SW152 SW152 Strike/MT Strike/MT Strike/MT Strike/MT AutoDoor AutoDoor AutoDoor AutoDoor SW154 SW154 SW151 SW151 8. Connecting Auto Door ( Contact Control ) 8. 2. Connect with two system & one door ◈ Lock Type Select Switch System 1 System 2 1) SW2 2) SW151~SW154 1) SW2 2) SW151~SW154 Auto Door Motor Auto Door Operating Part Auto-Door Monitor Sensor Input Line ◈ Wiring diagram 9P CONN Pin1 Pin3 Pin1 Pin2 (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 System 2 System 1
NC Strike ON NO/Motor Motor SW153 SW152 Strike/MT Strike/MT 1 2 3 4 5 6 AutoDoor AutoDoor SW154 SW151 9. Connecting Motor Lock ◈ Lock Type Select Switch 1) SW2 2) SW151~SW154 ◈ Wiring diagram Lock(+) Pin 1 Door Lock1 Door Lock2 Lock Ground Inside_Open Door_Monitor0 Door_Monitor1 Door_Monitor2 Ground (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 Lock(-) Pin 2 Ground Pin 3 Inside Open Pin 4 Door Monitor Pin 5 Open Monitor Pin 6 Close Monitor Pin 7 Pin 8 Inside Door Open S/W
ON NC Strike 1 2 3 4 5 6 NO/Motor Motor SW153 SW152 Strike/MT Strike/MT AutoDoor AutoDoor SW154 SW151 10. Connecting 2 Emergency Lamps ◈ Lock Type Select Switch Emergency Lamp 2 Emergency Lamp 1 1) SW2 2) SW151~SW154 Ground (-) Ground (-) 12 V (+) 12 V (+) ◈ Wiring diagram Pin 1 Door Lock1 Door Lock2 Lock Ground Inside_Open Door_Monitor0 Door_Monitor1 Door_Monitor2 Ground (Brown) - 1 (Red) - 2 (Black) - 3 (Orange) - 4 (Yellow) - 5 (Green) - 6 (Blue) - 7 (Black) - 8 Pin 2 Pin 3 Pin 8