1 / 17

The LHC Beam Position System

The LHC Beam Position System. Ad-hoc Working Group on LHC Experiment-Machine Parameter and Signal Exchange 26 th March 2002 Rhodri Jones (SL/BI). LHC BPM System - General. 100 Warm, Button Electrode BPMs (LEP) for TI2 & TI8 922 Button Electrode BPMs (24mm) for Arc & DS

felix-wagner
Download Presentation

The LHC Beam Position System

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. The LHC Beam Position System Ad-hoc Working Group on LHC Experiment-Machine Parameter and Signal Exchange 26th March 2002 Rhodri Jones (SL/BI)

  2. LHC BPM System - General • 100 Warm, Button Electrode BPMs (LEP) for TI2 & TI8 • 922 Button Electrode BPMs (24mm) for Arc & DS • 44 Warm Button Electrodes BPMs for IR3 & IR7 • 44 Enlarged Button BPMs (34mm) for IR1,2,5 & 8 • 24 Directional Couplers for IR1,2,5 & 8 • ~ 24 Special BPMs for Transverse Damper, Tune & Chromaticity Measurements in IR4 • 1 BPTX “timing pick-up” per incoming beam for IR1,2,5 & 8 • Total of 1166 BPMs for the LHC and its Transfer Lines LEMPSE - Rhodri Jones (SL/BI)

  3. The Arc BPM - SSS Layout LEMPSE - Rhodri Jones (SL/BI)

  4. 49mm aperture 24mm button Arc BPM - Button Feedthrough Button Feedthrough Beam Screen Liquid Helium Cooling Capillary LEMPSE - Rhodri Jones (SL/BI)

  5. Interaction Region BPMs Liquid Helium Capillaries • Stripline length 120mm to give same response as button • 2 Types • Warm Coupler - capable of withstanding bake-out to 200°C • Cold Coupler - located in Q2 cryostat (tilted by 45° for cryostat integration) • Directivity measured as 28dB at 200MHz Stripline Electrode Q2 Coupler LEMPSE - Rhodri Jones (SL/BI)

  6. The Front-End Electronics LEMPSE - Rhodri Jones (SL/BI)

  7. A + (B + 1.5ns) A B Beam 1.5ns B + 1.5ns The Wide Band Time Normaliser A B LEMPSE - Rhodri Jones (SL/BI)

  8. A B A + 1.5ns 1.5ns B + (A + 1.5ns) Dt depends on position The Wide Band Time Normaliser A + (B + 1.5ns) A B LEMPSE - Rhodri Jones (SL/BI)

  9. The Wide Band Time Normaliser A B A+(B+1.5ns) B+(A+1.5ns)+10ns Interval = 10  1.5ns System output LEMPSE - Rhodri Jones (SL/BI)

  10. The Wide Band Time Normaliser LEMPSE - Rhodri Jones (SL/BI)

  11. WBTN - Linearity v Intensity For LHC Arc BPMs 1% ~ 130mm LEMPSE - Rhodri Jones (SL/BI)

  12. WBTN - Linearity v Position For LHC Arc BPMs 1% ~ 130mm LEMPSE - Rhodri Jones (SL/BI)

  13. Very Front-End WBTN Card 70MHz Low Pass Filters Supplied by TRIUMF (Canada) 1310nm Diode Laser Transmitter Single-Mode Fibre-Optic Link VME based Digital Acquisition Board TRIUMF (Canada) WBTN Mezzanine Card (10bit digitisation at 40MHz) The LHC BPM Acquisition System Tunnel Surface LEMPSE - Rhodri Jones (SL/BI)

  14. 3 = 750mm 20% of 4mm Closed Orbit ‘budget’ (Spec = 500mm) Accuracy and Resolution LEMPSE - Rhodri Jones (SL/BI)

  15. ~150m to the IP Timing Pick-up for the Experiments(BPTX) • Located ~150m from the IP in front of the D2 Magnet • One BPTX either side of the IP on the incoming beam • Exclusively used by the experiments LEMPSE - Rhodri Jones (SL/BI)

  16. BPTX Requirements? Choice of Pick-up? • Stripline Coupler? • Peak voltage (one button) of ~20V after 200m of cable for nominal bunch • Peak voltage (one button) of ~1V after 200m of cable for pilot bunch • Button Electrode BPM? • Peak voltage (one button) of ~5V after 200m of cable for nominal bunch • Peak voltage (one button) of ~250mV after 200m of cable for pilot bunch • Other Type of Pick-up? Type of Signal? • Sum signal (sum of all 4 pick-up electrodes  2  peak voltage)? • Virtually independent of position & requires only 1 cable • Sum and Delta Signal? • Requires 3 cables to give sum, horizontal position & vertical position • Other Type of Signal? LEMPSE - Rhodri Jones (SL/BI)

  17. Next Steps SL/BI will supply: • 2 BPTX Pick-ups per Experiment • Choice of pick-up in collaboration with Experiments Experiments responsible for: • Cabling • All machine cabling to be defined by 15th March 2002! • All machine cabling to be ordered by 15th May 2002 • Any subsequent electronics • Keep in mind radiation resistance for electronics in the tunnel LEMPSE - Rhodri Jones (SL/BI)

More Related