1 / 21

Thermal Control Design J.D. Huang ( 黃正德 ) Mechanical Engineering Section

Thermal Control Design J.D. Huang ( 黃正德 ) Mechanical Engineering Section National Space Program Office April 14, 2005. Contents. Key Requirements Thermal Information Geometric Mathematical Model Assumptions Thermal Analysis Cases Thermal Analysis Results Conclusions.

gamma
Download Presentation

Thermal Control Design J.D. Huang ( 黃正德 ) Mechanical Engineering Section

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Thermal Control Design J.D. Huang (黃正德) Mechanical Engineering Section National Space Program Office April 14, 2005

  2. Contents • Key Requirements • Thermal Information • Geometric Mathematical Model • Assumptions • Thermal Analysis Cases • Thermal Analysis Results • Conclusions

  3. Key TCS Requirements • Passive thermal control • The thermal control should be achieved through passive elements, as thermal blankets, insulation, and surface finishes. • Materials should be selected for low-outgassing characteristics. • Thermal margin • For components that have no thermal control or have passive control only, an uncertainty margin of 5. • Heaters • If thermostats are used, the thermostat shall be redundant. • Each heater shall be provided with a ground-commandable override capability. • Each heater shall be sized to control to 5 deg C above its minimum allowable temperature or to control the component at its minimum allowable temperature with 25% excess control authority.

  4. Thermal Information - Attitude • Altitude : 400 ~ 800 km • Beta angle : -90 ~+90 deg • Attitude : Normal mode, Safehold mode, Orbit Control mode

  5. Thermal Information- Temperature Limits • Payload Operating (°C) Non-operating (°C) • GPS Occ. Rx : -20 to +60 -30 to +70 • GPS Occ. Ant. -125 to +105 -125 to +105 • TBB -10 to +50 -20 to +70 • TBB Ant. -125 to +105 -125 to +105 • TIP -10 to +50 -10 to +50 • SSR/PC -10 to +40 -25 to +40 • BUS • Power • Battery -5 to +30 -5 to +30 • BCR+PDU -25 to +50 -35 to +60 • Solar Array -100 to +105 -100 to +105 • C&DH • SBFC -20 to +65 -45 to +70 • IIU -20 to +65 -45 to +70 • Mass Memory -20 to +65 -45 to +70

  6. Thermal information-Temperature Limits (Continued) ADCS Operating (°C) Non-operating (°C) Torque Rods -30 to +40 -50 to +61 Reaction Wheel -10 to +50 -35 to +61 Sun Sensor -95 to +80 -105 to +90 Earth Sensors -40 to +40 -40 to +61 IRU (3-axis) -25 to +55 -25 to +55 Magnetometer -60 to +50 -60 to +50 GPS Rx. -10 to +40 -25 to +40 GPS Ant. -55 to +71 -55 to +71 TT&C Hybrid -10 to +40 -25 to +40 Diplexer -10 to +40 -25 to +40 Transceiver -10 to +40 -25 to +40

  7. Thermal information-Temperature Limits (Continued) Propulsion Operating (°C) Non-operating (°C) Latching Valve +7 to +55 +7 to +55 Press. Transducer +7 to +55 +7 to +55 Thruster +7 to +55 +7 to +55 Tank +7 to +55 +7 to +55 Filter +7 to +55 +7 to +55 Fill Drain Valve +7 to +55 +7 to +55

  8. Thermal Information- Power Dissipation

  9. Thermal Information- Power Dissipation (Continued)

  10. Geometric Mathematical Model • Internal model MLI Radiator L-Band S-Band RW SSR/PC TBB C&DH ADCS GPS RX Torque Rod PDU Tank TIP LACH VALVE Battery BCR GPS Occ. x x y y z z

  11. Geometric Mathematical Model (Continued) • External model • Orientation (Normal Mode) Eclipse Earth Earth Orientation Sun • Orientation (Safe-hold Mode) Rotation Rate=2 rev./orbit Eclipse Earth Sun Orientation Sun

  12. Assumptions • +Y and –Y side solar panels will be deployed to 90 deg from the stowed condition and decoupled from the spacecraft bus. • Thermal capacitance of each component is assumed to be 900 (J/kg°C) x mass (kg). • Contact conductance of battery is assumed to be 200 (W/m2°C) and Others are 30 (W/m2°C). • RCS tank is isolated ( 0.01 W/°C ) from deck and covered with MLI to reduce the internal radiation coupling with other components. • Heat conductions between deck and the side panels are through eighteen(18) M4 screws with the value of conductance of 0.76 (W/m2°C).

  13. Thermal Analysis Cases

  14. Thermal Analysis Results-Radiator & Required Heater Power

  15. Thermal Analysis Results-Temperature Prediction • The worst hot and cold temperatures for Normal Operating.

  16. Thermal Analysis Results-Temperature Prediction (Cont’) • The worst hot and cold temperatures for Safe-hold Mode.

  17. Thermal Analysis Results-Temperature Plots • Normal Hot, H=400 km, =0o • Normal Hot, H=800 km, =0o Daytime Daytime Daytime Eclipse Daytime Eclipse

  18. Thermal Analysis Results-Temperature Plots (Continued) • Normal Hot, H=400 km, =90o • Normal Hot, H=800 km, =90o (10 Orbits) (10 Orbits) (10 Orbits)

  19. Thermal Analysis Results-Temperature Plots (Continued) • Normal Cold, H=800 km, =0o • Normal Cold, H=800 km, =90o (10 Orbits)

  20. Thermal Analysis Results-Temperature Plots (Continued) • Safe-hold Mode, H=800 km, =0o • Safe-hold Mode, H=800 km, =61o (10 Orbits) (10 Orbits)

  21. Conclusions • For both normal operating and safe-hold modes, all worst hot and cold predicted temperatures are within the operating/non-operating temperature ranges with proper margins. • The total required radiator areas on the side panels are 0.42 m2. • The total maximum required heater powers are 11.74 W for the normal operating mode and 18.1 W for safe-hold mode. • The predicted radiator areas and heater powers can be reduced if less power consumption is required. • All the thermal analysis results will be updated again if further design information is given.

More Related