240 likes | 396 Views
Air Interface. Analog Transmission. In analog transmission, the state of line can vary continuously and smoothly among an infinite number of states States can be signal strengths, voltages, or other measurable conditions
E N D
Analog Transmission • In analog transmission, the state of line can vary continuously and smoothly among an infinite number of states • States can be signal strengths, voltages, or other measurable conditions • Human voice is analog; telephone mouthpiece generates analogous electrical signal Strength Time
Digital Transmission • Time is divided into fixed-length clock cycles • Modems: a few thousand clock cycles per second • LANs: millions of clock cycles per second • The line is kept in one of only a few possible states (conditions) during each time period • this is why the signal must be kept constant • At the end of each time period, the line may change abruptly to another of these few states
Digital Versus Binary Transmission • Digital transmission:a few states • Binary transmission:exactly two states (1 and 0) • Binary is a special case of digital Few States Two States 1 0 Digital Binary
Digital Versus Binary Transmission • Sender and Receiver associate one or more bits with each state • Simplest case: High state = 1, Low state = 0 • If four states, might have the following: • Highest = 11 • Second highest = 10 • Next highest = 01 • Lowest = 00
Wire Propagation Effects • Propagation Effects • Signal changes as it travels • If change is too great, receiver may not be able to recognize it Original Signal Final Signal Distance
Distance Wire Propagation Effects: Attenuation • Attenuation: Signal Gets Weaker as it Propagates • May become too weak for receiver to recognize • Distortion: Signal changes shape as it propagates • Adjacent bits may overlap • May make recognition impossible for receiver Signal Strength Distance
Wire Propagation Effects: Noise • Noise: Thermal Energy in Wire Adds to Signal • Noise floor is average noise energy • Noise spikes are random energy affecting bits Spike Signal Signal Strength Error Noise Noise Floor Time
Signal Strength Signal Wire Propagation Effects • Noise and Attenuation • As signal attenuates, gets closer to noise floor • Smaller spikes can harm the signal • So noise errors increase with distance, even if the average noise level is constant • Want a high Signal-to-Noise Ratio (SNR) • Signal strength divided by average noise strength • As SNR falls, errors increase Noise Floor SNR Distance
Wire Propagation Effects: Noise & Speed • Noise and Speed • As speed increases, each bit is briefer • Noise fluctuations do not average out as much • So noise errors increase as speed increases OK Error One Bit One Bit Noise Spike Noise Spike Low Speed (Long Duration) High Speed (Short Duration) Average Noise During Bit Average Noise During Bit
Wire Propagation Effects: Interference • Interference • External signal converted to electrical energy • Adds to signal, like noise • Often intermittent (comes and goes), so hard to diagnose • Often called electromagnetic interference (EMI) Signal Signal Strength Interference
- + Interference Signal Single Twist Wire Propagation Effects: Cross-Talk Interference • Cross-Talk Interference • Multiple wires in a bundle each radiates its signal • Causes “cross-talk” interference in nearby wires • Wire Usually is Twisted • Several twists per inch • Interference adds to signal over half twist, subtracts over other half
Practical Issues in Propagation Effects • Distance limits in standards prevent serious propagation effects • Usually 100 meters maximum for ordinary copper wire • Problems usually occur at connectors • Crossed wires • Poor connections • Cross-talk interference
Radio Propagation • Broadcast signal • Not confined to a wire
Radio Waves • When Electron Oscillates, Gives Off Radio Waves (electromagnetic waves) • Single electron gives a very weak signal • Many electrons in an antenna are forced to oscillate in unison to give a practical signal
Radio Propagation Problems • Wires Propagation is Predictable • Signals go through a fixed path: the wire • Propagation problems can be easily anticipated • Problems can be addressed easily • Radio Propagation is Difficult • Signals begin propagating as a simple sphere • Inverse square law attenuation • If double distance, only ¼ signal strength • If triple distance only 1/9 signal strength • Signals can be blocked by dense objects • Creates shadow zones with no reception Shadow Zone
Radio Propagation Problems • Radio Propagation is Difficult • Signals are reflected • May arrive at a destination via multiple paths • Signals arriving by different paths can interfere with one another: called multipath interference • Can be constructive or destructive interference • Very different reception characteristics with in a few meters or centimeters
Radio Propagation: Waves • Waves 1 Frequency in hertz (Hz) Cycles per Second 3 One Second 7 Cycles Wavelength (meters) 4 Amplitude (strength) 2 1 Hz = 1 cycle per second
Radio Propagation: Frequency Spectrum • Frequency Spectrum • Frequencies vary (like strings in a harp) • Frequencies measured in hertz (Hz) • Frequency spectrum: all possible frequencies from 0 Hz to infinity • Metric system • kHz (1,000 Hz) kilohertz; note lower-case k • MHz (1,000 kHz) megahertz • GHz (1,000 MHz) gigahertz • THz (1,000 GHz) terahertz 0 Hz
Radio Propagation: Service Bands • Service Bands • Divide frequency spectrum into bands for services • A band is a contiguous range of frequencies • FM radio, cellular telephone service bands etc. Cellular Telephone Service Bands FM Radio AM Radio 0 Hz
Radio Propagation: Channels and Bandwidth • Service Bands are Further Divided into Channels • Like television channels • Bandwidth of a channel is highest frequency minus lowest frequency • Example • Highest frequency of a radio channel is 43 kHz • Lowest frequency of the radio channel is 38 kHz • Bandwidth of radio channel is 5 kHz (43-38 kHz) Channel Bandwidth Channel 3 Service Band– FM Radio Channel 2 Channel 1 0 Hz
Maximum Possible Speed Bandwidth Radio Propagation: Channels and Bandwidth • Shannon’s Equation -- W = B Log2 (1+S/N) • W is maximum possible (not actual) transmission speed in channel • B is bandwidth of channel: highest frequency - lowest frequency • S/N is the signal-to-noise ratio • The wider the channel bandwidth (B), the faster the maximum possible transmission speed (W)
Broadband vs. Baseband • Baseband: Inject signal into medium & propagates • Broadband: Different signals sent different channels • Begin with baseband signal • Modulate to fit in radio frequency signal (RF) • Channel bandwidth is wide = broadband transmission • Channel bandwidth is narrow = narrowband transmission