560 likes | 834 Views
Guidance for Evaluation of Potential Groundwater Mounding Associated with Cluster and High-Density Wastewater Soil Absorption Systems (WSAS). International Groundwater Modeling Center Colorado School of Mines John McCray Eileen Poeter, Geoffrey Thyne, and Robert Siegrist. Funding.
E N D
Guidance for Evaluation of Potential Groundwater Mounding Associated with Cluster and High-Density Wastewater Soil Absorption Systems (WSAS) International Groundwater Modeling Center Colorado School of Mines John McCray Eileen Poeter, Geoffrey Thyne, and Robert Siegrist
Funding • NDWRCDP via U.S. EPA • National Decentralized Water Resources Capacity Development Project
Other Areas of Research • Modeling & experiments for nitrogen transport at site scale (field and columns) • Watershed modeling (N and P) ** • Geochemical modeling of P • Pharmaceuticals and emerging organic contaminants (field, lab, modeling) • Modeling infiltration of wastewater in trenches and effect of biomats and sidewalls. ** • Mines Park experimental field site on campus • Tours during the NOWRA meeting, and a workshop on watershed modeling and N modeling tools.
Small Flows Quarterly Paper • Poeter, E.P., McCray, J.E., Thyne, G.D., Siegrist, R.L., 2005. Designing cluster and high-density wastewater soil-absorption systems to minimize potential groundwater mounding, Small Flows Q., 6(1), 36-48. • Provided to you by e-mail. • More papers to be published in ASCE Journal fo Hydrologic Engineering (2006)
Past focused on vertical movement of water, however, insufficient capacity may result in • Excessive mounding on low permeability lenses/layers • Excessive raising of the water table • Lateral movement of water, which may cause effluent breakout on slopes in the vicinity, or to nearby natural water.
This report presents a methodology for: • Assessing potential for groundwater mounding and lateral spreading • Design guidelines • Selection of investigation techniques and modeling approaches Based on site conditions, system parameters, and the potential severity of mounding.
APPROACH Simple flowchart and rating system helps to evaluate the need for further action, and the level of sophistication required. Consider the potential for mounding, AND the consequences of failure.
If Modeling is Necessary • Evaluate perched mound on low K layers • Evaluate mounding of the water table • In both cases evaluate potential for side-slope breakout
Two general cases • “Perched” Water - Mounding due to water buildup on low-permeability layers below the leach field). • Water table mounding – water buildup on the natural water table.
Perched Mounding Problem • Surface breakout of wastewater • Breakout on a nearby slope.
Two general model types • Analytical models - • Solve equations for vertical water flow for simplified geometries and boundary conditions. • Solutions can usually be programmed into spreadsheet. • Numerical Models – • Need numerical computer program to solve. • More complicated geometries. • Can simulate “realistic” scenarios. • But need more subsurface data
Analytical Solution: Khan equations • Assumes • uniform geometries • two types of media: soils and the layer • saturated flow • constant wastewater infiltration rate • wastewater us uniformly applied across the infiltration area or “bed” • width of infiltration bed is much smaller than the length (conservative assumption)
Surface Breakout: Design Variables • Total wastewater volume flow: Q • Area (A) available for infiltration basin • A includes the space between trenches • Effective wastewater infiltration rate: q’ = Q/A • Width (W) of infiltration basin. • Half-width (w) = 0.5 W • Length of infiltration basin “into the page”. LIB > W • Height (H) of saturated mound above low-perm layer • H must not reach surface AND it should allow a sufficient thickness of unsaturated soil (d1) for effective treatment.
Design Variables • Want to maintain H smaller than HMAX • K1 and K2 are fixed • Assuming fixed Q, design variables include: • W • A or LIB • q’ • Spacing between trenches. • Q may be a design variable • NO UNIQUE COMBINATION of design parameters exist. Design is iterative.
Design Tool: Excel Spreadsheet • Site characterization to obtain values for K. • First cut: choose statistical “best guess” based on soil type. • Better cut: conduct measurement of K • Start with “ideal configuration” for design variables. • Vary design parameters to achieve most desirable conditions (optimize area, dimension, trench spacing, total flow, etc.) • Analysis tools in excel allow one to apply equation to minimize or maximize any variable. • Design “nomographs” make this easier.
Typical Minnesota Soils Clarion • 3% slope - glacial till landscape • 0-36" loam texture: subangular blocky structure • 36-60" clay loam texture, massive structure • Seasonal saturation @ 36" Zimmerman • 3% slope - glacial outwash landscape • 0-44" fine sand: subangular blocky structure and single grain • 44-80" Banding of fine sand and loamy fine sand • No seasonal saturation to a depth of 80"
Clarion Soil Example Kloam = 25 cm/day K clayloam = 6.2 cm/day
Clarion Soil Example • No mounding on the low-K layer (clay loam) for: • q’ < K clay loam or q’ < 6.2 cm/day • For q’ > 6.2 cm/day, evaluate mounding • 36” to clay loam, assume need 2 ft unsat soil for treatment, then hmax = 1ft., or 0.31m
Clarion Soil Example: Spreadsheet Analysis 2 ft unsat soil No surface breakout
Clarion Soil Example: Uncertainty in K2 ? Reduce K2 by factor of 5
Clarion Soil Example: Conclusion • Reasonable widths of infiltration areas can be achieved. • Recall: width must be shorter than length for equation to be valid. • Mounding somewhat sensitive to actual value of K2 • May need to measure K1 and K2 • Talk about this latter
Side Slope Breakout: Design Variables • Same as previous, but also: • H must not reach surface at any location along slope. • Limiting case is depth of low-perm layer at base of slope (assuming ideal geometries). • May need to consider H at an arbitary distance XS from the center of the infiltration basin. • Should allow a sufficient thickness of unsaturated soil (d1) for effective treatment.
Khan equations: Side-slope breakout Slope intersects with low-perm layer Base of slope lies above the top of low-perm layer
What Soils Data do you Need? Location of Layers Soil type of layers Hydraulic conductivity of Layers Will talk more about this in my next presentation.
Analytical vs. Numerical Models • Use analytical models for first-estimate, decide if cost of numerical model is warranted. • We tested analytical model versus numerical model that has less restrictive assumption. • Could play this game forever, test most likely cases. • Note: Numerical models are also simplifications, and require much more data input.
Numerical Solution: Hydrus2D 2 cm/day Simplest Case Preliminary results!!!
Heterogeneous Clay (#2) 2 cm/day More Complex Cases # 2 Heterogeneous Clay Uniform layer results
Case Study in Canada • Central Ontario • Sewage Treatment Plan • Leaching Bed – 84 m x 64 m • 4 sections, each 10 rows • Rows: 30.5 m x 0.45m, 2.1m spacing • 122,000 L/day (30,000 gal/day) caused ponding • 41,000 L/day (10,000 gal/day) – OK • Sandy Silt • K (slug tests) – 3.5x10-5 to 3.7x10-4 cm/s