570 likes | 991 Views
Sample Preparation for inorganic trace analysis Lecture 2. Ahmad Razali Bin Ishak Department of Environmental Health Faculty of Health Sciences UiTM Puncak Alam. Solid Samples. Introduction. Analysis for metals in solids-2 different approach
E N D
Sample Preparation for inorganic trace analysisLecture 2 Ahmad Razali Bin Ishak Department of Environmental Health Faculty of Health Sciences UiTM Puncak Alam
Introduction Analysis for metals in solids-2 different approach Direct analysis of solid-X-ray florescence (self study-assignment) After decomposition
Decomposition techniques involves liberation of analyte (metal) of interest from interfering matrix Using a reagent (mineral/oxidizing acids or fusion or flux) And/or Heat Problem- risk of contamination and loss of analytes
Dry ashing The simplest of all decomposition systems involves the heating of the samples in porcelain crucible in a muffle furnace in the presence of air at 400-800C After decomposition, the residue is dissolved in acid and transferred to a volumetric flask prior to analysis. Allow organic matter to be destroyed. May lead to the loss of volatile elements (Hg, Cd, Ca, As, Sb, Cr and Cu)
Cont.. Disadvantages of this method: • Loss due to volatilization • Resistance to ashing by some materials • Difficult dissolution of ashed materials • High risk of contamination • It has largely been replace by wet ashing
Wet digestion (Acid digestion) The use of mineral or oxidizing acids and an external heat sources to decompose the sample matrix. The choice of an individual acids is dependent upon the nature of the matrix to be decomposed
Once the choice of acid is made the sample is placed into an appropriate vessel for decomposition stage Vessel- carried out in open glass vessels(beakers or boiling tubes) using hotplate (in FSK) or multiple sample digester The US EPA method for acid digestion of sediments, sludges and soils are outlined in figure 1
The digestion of food stuffs can be carried out in a similar manner A typical procedure for digestion of foodstuffs e.g. cereals, meats, fish and vegetable for determination of total metal content (cadmium,cooper,iron, lead and zinc) in figure 2
Microwave digestion An alternative approach to conventional heating involves the use of microwave heating Advances in technology by a variety of manufacturers means that today there are two types of microwave heating systems commercially available : open-focused and closed vessel system.
Introduction Analysis of liquid samples for metals-required no sample pre-treatment-just a simple filtration (0.2 um)of the sample to remove particulates prior to introduction into chosen instrument. However, reality is often very different and even most sensitive of analytical technique (e.g. ICP-MS) may require some additional sample pre-treatment; separation or pre-concentration Pretreatment/pre-concentration-potential contamination-great care required
Liquid-liquid extraction Addition of a suitable chelating agent to the water samples to form metal complex Will effectively partition into an immiscible organic solvent Metal present in a large volume of sample water is effectively and quantitatively transferred into a small volume of organic solvent.
The important variables in LLE are as follows: Choice of chelating agent Choice of organic solvent pH of the aqueous sample The most commonly used chelating agent in AAS is Ammonium pyrrolidine dithiocarbamate (APDC). This reagent can be directly extracted with methyl isobutyl ketone (MIBK) as the organic solvent.
Sample preparation for organic analysisLecture 3 Ahmad Razali Bin Ishak Department of Environmental Health Faculty of Health Sciences UiTMPuncakAlam
Introduction New instrumental approaches-led to development -speed of extraction, reduction in organic solvent consumption and introduction of automation. However, this instrumental approaches-higher price tag than the conventional. Extraction of env. Pollutant from solid or semi solid matrices can be divided into several categories based on the method of extraction, mode of heating, and presence or not of some type of agitation.
Types of extraction-Solid Soxhlet extraction Shake flask extraction Ultrasonic extraction Supercritical Fluid Extraction (SFE) Microwave assisted extraction Pressurized Fluid Extraction Matrix solid phase dispersion
Soxhlet Extraction The basis of soxhlet extraction apparatus consist of a solvent reservoir, and extraction body, a heat sources (e.g. isomantle) and a water-cooled reflux condenser A soxhlet uses a range of organic solvent to remove organic compounds, primarily from solid matrices The solid sample (e.g. 10 g soil) and a similar mass of anhydrous sodium sulfate are placed in the porous thimble (cellulose) which in turn is located in the inner tube of Soxhlet apparatus
The apparatus is then fitted to a round- bottom flask of appropriate volume containing organic solvent of choice and to reflux condenser. The solvent is then boiled gently-The solvent vapor passes up through the tube is condensed by the reflux condenser and the condensed solvent falls into the thimble and slowly fills the body of soxhlet apparatus
When the solvent reaches the top of the tube, it syphons over into the round-bottomed flask the organic solvent containing the analyte extracted from the sample in the thimble. This solvent is then said to have completed one cycle. The whole process is repeated frequently until the pre-set extraction time is reached.
As the extracted analyte will normally have higher boiling point than the solvent, it is preferentially retained in the flask and fresh solvent re-circulates
Shake Flask Extraction Conventional LLE in the form of shake flask extraction is carried out by placing samples (e.g. soil) into a suitable glass container, adding a suitable organic solvent and the agitating or shaking
Ultrasonic extraction Sonication involves the use of sound waves to agitate a sample immersed in an organic solvent-using sonic probe or sonic bath The sample is placed in suitable glass container and enough organic solvent is then added to cover the sample. The system is then sonicated for a short period typically 3 min using sonic bath or probe After extraction, the solvent containing the analyte is separated by centrifugation and/or filtration and fresh solvent added. The whole process is repeated three times and all of the solvent extract are then combined.
Types of extraction-Liquid Liquid Liquid extraction (LLE) Solid phase extraction (SPE) Solid Phase Microextraction (SPME)
Liquid-Liquid Extraction The sample is distributed/partitioned into two immiscible solvent which analyte and matrix have different solubility Advantage-wide availability of pure solvent, low cost apparatus
Solid phase extraction Liquid-solid extraction Bringing a liquid sample into contact with a solid sorbent whereby the analyte is selectively adsorbed onto the surface of solid phase. The latter is then separated from solution and other solvents are added.
Solid Phase extraction The first solvent-wash to remove possible contaminant Then, Liquid sample bring into contact with a solid phase/sorbent whereby analyte is selectively adsorbed onto the surface of solid phase. The analyte then separated from the solid phase by eluting solvent. This solvent is then collected for analysis.
Solid Phase Micro Extraction (SPME) The process whereby an analyte is adsorbed onto the surface of a coated silica fiber as a method of concentration. This is follow by desorption of the analyte into a suitable instrument for separation and quantification
Introduction Volatile compounds in the atmosphere, workplace and on industrial sites need to be monitored with regard to safety consideration This VOC, can be trapped either on a solid support material (for thermal desorption) or liberated from water sample and then trapped (e.g. via purge and trap) prior to analysis.
Self study Thermal desorption Purge-and-trap