1 / 10

Timer/Counter

Timer/Counter. Pulse Width Modulation modes. There are two PWM modes of Timer/Counter 0. PWM mode is determined by bits WGM00:WGM01 1:1 – Fast PWM mode Timer/Counter counts from 0x00 to 0xFF After reaching 0xFF, rolls over to 0x00 and starts over 1:0 – Phase Correct PWM mode

leora
Download Presentation

Timer/Counter

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Timer/Counter Pulse Width Modulation modes CS-280 Dr. Mark L. Hornick

  2. There are two PWM modes of Timer/Counter 0 PWM mode is determined by bits WGM00:WGM01 • 1:1 – Fast PWM mode • Timer/Counter counts from 0x00 to 0xFF • After reaching 0xFF, rolls over to 0x00 and starts over • 1:0 – Phase Correct PWM mode • Timer/Counter counts from 0x00 to 0xFF to 0x00 • After reaching 0xFF, decrements back down to 0x00 and starts over CS-280 Dr. Mark L. Hornick

  3. In both PWM modes, the T/C counts all the way to MAX Counter value MAX= 0xFF OCR0 BOTTOM = 0x00 Fast PWM Mode ticks Counter value MAX= 0xFF OCR0 BOTTOM = 0x00 PWM Phase Correct Mode ticks CS-280 Dr. Mark L. Hornick

  4. Output Comparator behavior in PWM Modes Output Comparator can drive the voltage on OC0 (PB3) high or low • PB3 must be setup for output When in PWM modes, bits COM01:COM00 affect the operation as follows: • 0 0: OC0 disconnected • 0 1: Reserved • 1 0: Clear OC0 on compare match • 1 1: Set OC0 on compare match CS-280 Dr. Mark L. Hornick

  5. Signals on OC0 in Fast PWM mode Counter value MAX= 0xFF OCR0 BOTTOM = 0x00 Fast PWM Mode ticks COM01:COM00 = 1:1 Set OC0 on compare match COM01:COM00 = 1:0 Clear OC0 on compare match ticks Signal on OC0 CS-280 Dr. Mark L. Hornick

  6. Fast PWM Interrupts • OCF0 flag in TIFR is set when TCNT0=OCR0. When OCIE0 is enabled: • Compare Match interrupt is generated (ISR jump vector at 0x14) • OCF0 is automatically reset when ISR is executed • TOV0 is set when TCNT0 overflows from 0xFF to 0. When TOIE0 is enabled: • Overflow interrupt is generated (ISR jump vector at 0x16) • TOV0 is automatically reset when ISR is executed CS-280 Dr. Mark L. Hornick

  7. The duration of pulse width can be modulated by varying the value of OCR0 CS-280 Dr. Mark L. Hornick

  8. Behavior of OC0 in PWM Phase Correct mode Counter value MAX= 0xFF OCR0 BOTTOM = 0x00 PWM Phase Correct Mode ticks COM01:COM00 = 1:1 Set OC0 on compare match COM01:COM00 = 1:0 Clear OC0 on compare match ticks Signal on OC0 CS-280 Dr. Mark L. Hornick

  9. Phase-correct Interrupts • OCF0 flag in TIFR is set when TCNT0=OCR0. When OCIE0 is enabled: • Compare Match interrupt is generated (ISR jump vector at 0x14) • OCF0 is automatically reset when ISR is executed • TOV0 is set when TCNT0 decrements back to 0. When TOIE0 is enabled: • Overflow interrupt is generated (ISR jump vector at 0x16) • TOV0 is automatically reset when ISR is executed CS-280 Dr. Mark L. Hornick

  10. Pulse width modulation in Phase-correct operation CS-280 Dr. Mark L. Hornick

More Related