1 / 23

Air Flow Bench

luna
Download Presentation

Air Flow Bench

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

    1. Air Flow Bench Presented By: Saket Karajgikar & Nikhil Lakhkar Advisor: Prof. Dereje Agonafer

    2. Air Flow Experimental Bench

    3. Air flow bench Configuration

    4. Experimental Bench Contd… The chambers are designed in accordance with AMCA 210-99/ASHRAE 51-1999 and have been sized for convenient flow ranges The chamber diameter is determined by the size of the axial flow fan to be tested and the maximum flow range desired Lower flow ranges may be achieved by utilizing smaller nozzles in the nozzle array

    5. Experimental Bench Contd… They are positioned on the plate so that they may be used in parallel to achieve higher flow ranges. Stoppers are provided to block off nozzles not in use and are easily removed for different ranges of testing.

    6. Experimental Bench Contd… The chamber has flow straightening screens installed upstream and downstream of the nozzle array. The screens break up turbulence in the air stream and provide a uniform flow approaching the nozzle array.

    7. Experimental Bench Contd… The flow through the chamber is controlled with a sliding gate valve called a blast gate. By opening the blast gate, the flow is varied through the chamber to provide test data from shut off (no flow) to free delivery (no back pressure) for fan performance evaluation.

    8. Applications of Air Flow Bench Air Flow Bench is used for: To calculate the Air Flow Rate Fan Performance Curve Measurement Thermal Resistance

    9. Air Flow Rate where, Q = Air Flow Rate (m3/min) A = Nozzle Sectional Area (m2) V = Average Flow Velocity through nozzle (m2/sec) where, g = gravitational acceleration 9.8 m/s2 Pn = Differential Pressure r = Specific Gravity of Air (1.2 kg/M3 at 20oC, 1atm)

    10. Fan Performance Curve A fan performance curve characterizes the ability of the fan to drive air against a flow resistance It is plotted as static pressure drop in inches of water gauge pressure (iwg) against air flow in cubic feet per minute (cfm) The measurement starts with the air flow chamber blocked so no flow occurs (i.e. 0 cfm) and proceeds with greater and greater flow rates until the static pressure has dropped to zero representing the "free delivery" condition

    11. Fan Performance Testing The purpose of this test is to determine the aerodynamic characteristics of the fan under test Data is taken from no flow (shut off) to free flow (free delivery) Curve is plot using these data points

    12. Fan Performance Testing Experimental Set-up Nozzle is selected based on required flow range Nozzles should always point downstream Fan to be tested is mounted on the front plate of the chamber Fan should be sealed adequately to prevent leakage

    13. Fan Performance Testing Experimental Procedure First data point is considered at no flow or shut off condition At this point differential pressure is zero Start the counter blower at low speed Slowly open the blast gate until 0.1 inches w.g. is measured for the differential pressure Allow the fan to stabilize and record the data

    14. Fan Performance Testing Experimental Procedure (Contd…) Record the data points for different Blast gate opening As the experiment proceeds, differential pressure increases and static pressure decreases Continue taking data points till free delivery is reached (I.e zero static pressure) Shut off the counter blower and plot the data Data points fully define the fan performance curve

    15. Typical Performance Curve

    16. System Impedance Testing Purpose for this test is to determine the pressure required to move the appropriate amount of volume flow through the system For the impedance test, the air is forced through the unit to be tested and the pressure drops are measured for various flow points

    17. System Impedance Testing Experimental Procedure Open the blast gate completely Start the counter blower and blow air through the unit to be tested The first data point should be a minimum of 0.1 inches w.g. differential pressure Take 5 to 6 data by increasing the counter blower speed

    18. Typical System Resistance Curve

    19. Theoretical Operating Point Superimpose Performance curve on Impedance Curve. Intersection of the two curves represents theoretical operating point of the fan.

    20. Thermal Resistance With the evolution of the personal computer, the cooling of high power components has moved to the forefront of system design Over the years the power dissipation in the PC s microprocessor has been increasing steadily For this reason, the use of heat sinks in computers has become more common By measuring thermal resistance as a function of free stream velocity, thermal designers can predict the performance of heat sinks in their system and predict the temperature of components

    21. Calculation of thermal resistance The airflow chamber is used as the air source for the system For a given volume of air drawn through the system temperatures are measured Thermal resistance is calculated by: where, Tcomponent = Case temperature of component Tambient = Ambient temperature upstream of the heat sink Pcomponent = Power dissipation of component Rthermal = Thermal Resistance

    22. Calculation of thermal resistance (Contd..) *Graph of Thermal Resistance Vs. Approach velocity is plotted

    23. Thank You!

More Related