1 / 29

Street Rod Jeopardy

Street Rod Jeopardy.      Hydraulic brake lines are made of A. Steel B. Copper C. Brass D. Aluminum 10.     The purpose of the rubber strap wrapped around the brake drum during resurfacing on the lathe is to A. maintain drum to cutter contact prevent drum expansion

macaulay-peck
Download Presentation

Street Rod Jeopardy

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Street Rod Jeopardy

  2.      Hydraulic brake lines are made of A. Steel B. Copper C. Brass D. Aluminum 10

  3.     The purpose of the rubber strap wrapped around the brake drum during resurfacing on the lathe is to • A. maintain drum to cutter contact • prevent drum expansion • C. aid in producing a better finish • do all of the above20

  4.   When replacing brake shoes on most domestic vehicles, A.The shoe with the short lining is installed toward the front of the vehicle B. The shoe with the short lining is installed toward the rear of the vehicle C. The primary shoe installs towards the rear D. Either shoe may be installed in either position.30

  5.    If the brake pedal of a vehicle pulsates rapidly when applying the brakes, the problem could be caused by the • out-of-round tires • worn disc pads • uneven hydraulic pressure • excessive rotor runout. 40

  6.  Square cut caliper seals will • act as an hydraulic seal • act as a self adjuster • act as a return mechanism for the piston • D.do all of the above 50

  7. The four strokes of the four stroke cycle occur in which sequence? A.     COMPRESSION, INTAKE, POWER, EXHAUST B.     COMPRESSION, EXHAUST, POWER, INTAKE C.     INTAKE, COMPRESSION, POWER, EXHAUST D. INTAKE, POWER, EXHAUST, COMPRESSION 10 1.T 1.

  8. How many degrees must a crankshaft rotate to complete all four strokes of a four-stroke cycle engine. A.     180 B.     360 C.     540 D. 72020

  9. Daily Double The volume that the piston pushes out as it moves from BDC to TDC in the cylinder is called. A.     Compression Ratio B.     Compression Pressure C.     Cubic inch displacement D. None of the above

  10. The movement of the piston from TDC to BDC is called a   A. Stroke   B. Cycle C. Rotation 40

  11. The movement of the piston from TDC to BDC creates A.  Pressure B.  Blow-by C.  Cubic Inches D. Vacuum 50

  12. The same belt that drives the water pump may also drive the alternator. TRUE or FALSE 10

  13. Three electrical terms are: A.  OHMS, AMPS, RPM’S B.  VOLTS, OHMS AMPS C.  RPM’S WATTS, CURRENT D. TURBO, FLUX CAPACITOR, AMPLITUDE20

  14. Most automotive electrical circuits are protected by A.     Circuit Breakers B.     Fuses C.     Relays D. Gauges30

  15.      Charging system voltage must fall between: • A.   5-12 • B.    13-15 • C.   12-20 • 20,000-40,000 • 40

  16. A bi-product of electron movement is: A.   Heat B.   Water C.   Voltage D. Absolute Zero50

  17. 10 THE DISTRIBUTOR ROTOR IS MOUNTED A. IN THE HOUSING B. ABOVE THE CAP C. ABOVE THE BREAKER CAM D. NONE OF THE ABOVE

  18. TWO TYPES OF PISTON RINGS ARE: A. COMPRESSION AND LOCKING B. COMPRESSION AND OIL CONTROL C. COMPRESSION AND POWER D. COMPRESSION AND SEALING 20

  19. What term is used to describe the ability of an object or material to allow electricity to pass through it? (not a measurement) A. Continuity B. Amps C. Insulation D. Ohms 30

  20.     The scientific abbreviation for raw fuel is: A.   CO B.    O2 C.   HC D. NO x 40

  21. What is the term when a full circle is provided for electrical flow. • A. Semiconductor • B. Conductor • C. Circuit • D. Voltage drop 50

  22. What is not a good conductor of electricity. A. Wood B. Saltwater C. Copper D. Lead 10

  23. The name of the tool used to check for • The name of the tool used to check for power only is the _________________________ • Muti-meter B. Test-light • C. Ohm meter D. Continuity tester • 20 • _____________________________ • Muti-meter B. Test-light C. Ohm meter D. Continuity tester

  24. What is solder made from? ______________________________ A. Zinc B. Gold C. Iron D. Lead 30

  25. The coil or armature is gapped at what measurement to the flywheel? A.001 B. .010 C. .030 D. .100 40

  26. The ignition coil on a small engine has what on the flywheel to generate voltage? A. key B. magnets C. weights D. fins 50

  27. Wrong Answer Back to the question

  28. You Are Correct! Back to the board

  29. Final Jeopardy Category: BOATS A. WHAT IS THE NAME OF THE BOTTOM MOST EDGE OF THE HULL AND (B) THE DISTANCE FROM IT TO THE WATER LINE ON THE SIDE OF THE HULL?.

More Related