1 / 28

Thermionic emission

Thermionic emission. If a tungsten filament is heated to about 2000 o C, some of the electrons have sufficient kinetic energy to escape from the surface of the wire. This effect is called thermionic emission .

philip-mccarthy
Download Presentation

Thermionic emission

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Thermionic emission • If a tungsten filament is heated to about 2000 o C, some of the electrons have sufficient kinetic energy to escape from the surface of the wire. • This effect is called thermionic emission. • It is quite easy to imagine this if we think about a metal wire as a lattice of ions in a sea of free electrons. In effect we are boiling the electrons off.

  2. Thermionic Diode • In the vacuum tube there are two electrodes • Cathode -veAnode +ve • When the filament is switched on electrons start to flow from the cathode the tungsten filament and are attracted to the anode • You need a vacuum as the electrons would collide with the gas particles. Also the filament would burn up • Thermionic_diode

  3. Deflection tube • The electron gun consists of a heated filament/cathode and an anode with a hole in it. • This produces a narrow beam of electrons • The screen is coated with a fluorescent material which glow when electrons strike it.

  4. Deflection Tube

  5. Defection by an electric field • The negatively charged electrons are attracted towards the positive plate.

  6. Deflection tube • In a magnetic field the electron is deflected depending on the direction of the magnetic field - Use Lenz’s left hand rule.

  7. Cathode Ray Tubes Thermionic emission was the starting point for Joseph John Thomson to produce his cathode ray tube (CRT) in 1897, the descendants of which we used to see every day, before TFT (thin film transistor) TV sets became more common. • Now do question 1 page 243

  8. Using an Oscilloscope

  9. Learning Objectives To know what an oscilloscope is and how it works. The job description of the oscilloscope’s main parts How the oscilloscope shows Direct Current DC and Alternating Current AC Nocalculations are required in the exam for the voltage, time period or frequency

  10. Cathode Ray Oscilloscope

  11. Definition From the specification book:- An oscilloscope consists of a specially made electron tube and associated control circuits. The electron gun emits electrons towards a fluorescent screen  light is emitted when electrons hit the screen  this is what we see.

  12. Tube Photograph

  13. Electron Gun Photograph

  14. Tube Diagram y plates - amplifier anode x plates - timebase heater supply - + fluorescent screen H.T. supply

  15. Cathode Ray Oscilloscope (CRO) Time base Display Y-gain My tie Channel1 Channel 2

  16. How does it work? • An oscilloscope consists of a specially made electron tube and associated control circuits. • An electron gun at one end of the glass tube emits electrons in a beam towards a fluorescent screen at the other end of the tube. • Light is emitted from the spot on the screen where the beam hits the screen.

  17. How does it work? • When no p.d. is applied across the plates the spot on the screen is stationary. • If a pd is applied across the X-plates the beam of electrons is deflected horizontally and the spot moves across. • pd across Y-plates  spot moves up and down.

  18. Reading the CRO 1 Peak-to-Peak voltage To get the time period you need to measure this distance and convert it to time by multiplying by the time base setting Time Period (ms)

  19. Oscilloscope Controls • The x-plates are connected to a time base circuit which is designed to make the spot move across the screen in a given time  then back again much faster.  a bit like a trace on a heart monitor. • The y-plates are connected to the Y-input and this causes the spot to move up or down depending on the input pd.

  20. summary electron gun produces a beam of electrons light produced on the screen by electron beam a p.d. across the y plates deflects the trace vertically a p.d. across the x plates deflects the trace horizontally y plates anode heater supply x plates - + phosphor screen H.T. supply

  21. Displaying a waveform1. The time base • The X-plates are connected to the oscilloscope’s time base circuit. • This makes the spot move across the screen, from left to right, at a constant speed. • Once the spot reaches the right hand side of the screen it is returned to the left hand side almost instantaneously. • The X-scale opposite is set so that the spot takes two milliseconds to move one centimetre to the right. (2 ms cm-1). NTNU Oscilloscope Simulation KT Oscilloscope Simulation

  22. Gain and Time-Base Controls

  23. Displaying a waveform2. Y-sensitivity or Y-gain • The Y-plates are connected to the oscilloscope’s Y-input. • This input is usually amplified and when connected to the Y-plates it makes the spot move vertically up and down the screen. • The Y-sensitivity opposite is set so that the spot moves vertically by one centimetre for a pd of five volts (5 V cm-1). • The trace shown appears when an alternating pd of 16V peak-to-peak and period 7.2 ms is connected to the Y-input with the settings as shown. NTNU Oscilloscope Simulation KT Oscilloscope Simulation

  24. Peak Voltage Peak p.d. = 3 Divisions x 1.0 mV/div = 3.0 mV

  25. Period & Frequency period = 4.0 divisions x 1.0 ms/div = 4.0 ms frequency = 1 / period frequency = 1 / 0.004 s frequency = 250 Hz

  26. Measuring d.c. potential difference All three diagrams below show the trace with the time base on and the Y-gain set at 2V cm-1. Diagram a shows the trace for pd = 0V. Diagram b shows the trace for pd = +4V Diagram c shows the trace for pd = -3V. NTNU Oscilloscope Simulation KT Oscilloscope Simulation

  27. Self Test

  28. Internet Links • Oscilloscope - basic display function - NTNU • Oscilloscope Simulation - by KT • Lissajous figures - Explore Science • Lissajous figures- by KT

More Related