1 / 41

PROSTHETIC PROCEDURE MANUAL AR SYSTEM

PROSTHETIC PROCEDURE MANUAL AR SYSTEM. CEMENTED RESTORATION. Impression Copings. Cemented Abutment. Pick-up. Set Screw. Implant Analog. Angled Abutment. Transfer. IMPRESSION COPINGS Implant Level – Pick-up. 1.2mm Hex Driver. Guide Pin. Engaging.

sandro
Download Presentation

PROSTHETIC PROCEDURE MANUAL AR SYSTEM

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. PROSTHETIC PROCEDURE MANUALAR SYSTEM

  2. CEMENTED RESTORATION Impression Copings Cemented Abutment Pick-up Set Screw Implant Analog Angled Abutment Transfer

  3. IMPRESSION COPINGSImplant Level – Pick-up 1.2mm Hex Driver Guide Pin Engaging • Implant level impression, pick-up impression coping (open tray technique) • Impression coping is packaged with corresponding guide pin • Use 1.2mm Hex driver to assemble/ disassemble

  4. IMPRESSION COPINGSImplant Level – Transfer 1.2mm Hex Driver Guide Pin Engaging • Implant level impression, transfer impression coping (closed tray technique) • Impression coping is packaged with corresponding guide pin • Use 1.2mm Hex driver to assemble/ disassemble

  5. IMPLANT ANALOG

  6. CEMENTED ABUTMENT 1.2mm Hex Driver DIAMETER HEIGHT CUFF Engaging Fastening torque 30 Ncm

  7. ANGLED ABUTMENT 1.2mm Hex Driver DIAMETER HEIGHT CUFF Engaging • Options of 15 degrees and 25 degrees • Angled Abutments are packaged alongside corresponding set screw • Fastening torque 30 Ncm

  8. SET SCREW DIAMETER LENGTH • Cemented Abutment screw is 10mm long • Angled Abutments screw is 8mm long • Set screws are packaged along with corresponding abutment

  9. CLINICAL PROCESSFixing Impression Copings (1/3) • View of patient’s mouth

  10. CLINICAL PROCESSFixing Impression Copings (2/3) • Remove healing abutment / cover screw with 1.2mm Hex Driver • Insert impression coping inside corresponding implant connection

  11. CLINICAL PROCESSFixing Impression Copings (3/3) • Fasten impression coping with corresponding guide pin • Tighten guide pin with 1.2mm hex driver

  12. CLINICAL PROCESSTaking The Impression (1/6) • Apply the light impression material on corresponding site of oral cavity

  13. CLINICAL PROCESSTaking The Impression (2/6) • Pour the heavy impression material inside the impression tray

  14. CLINICAL PROCESSTaking The Impression (3/6) • Position tray for impression taking • Apply pressure until top part of guide pin appears • wait for impression material to set • Transfer impression copings will require prefabricated tray • Pick-up impression copings will require previously customized tray

  15. CLINICAL PROCESSTaking The Impression (4/6) • Remove guide pin

  16. CLINICAL PROCESSTaking The Impression (5/6) • Check tray for impression errors / success

  17. CLINICAL PROCESSTaking The Impression (6/6) • Replace healing abutment / cover screw in corresponding site

  18. LABORATORY PROCESS1. Fixing Analogs & Making Artificial Gum (1/4) • Fix analogs on corresponding impression coping

  19. LABORATORY PROCESS1 - Fixing Analogs & Making Artificial Gum (2/4) • Apply (Spray) separating product on impression areas

  20. LABORATORY PROCESS1. Fixing Analogs & Making Artificial Gum (3/4) • Apply artificial gum product on intervention area • Wait for product to dry

  21. LABORATORY PROCESS1. Fixing Analogs & Making Artificial Gum (4/4) • Trim gum

  22. LABORATORY PROCESS2. Master Modeling (1/3) • Prepare (mix) the stone

  23. LABORATORY PROCESS2. Master Modeling (2/3) • Pour the mixed stone inside the impression

  24. LABORATORY PROCESS2. Master Modeling (3/3) • Master model finishing work

  25. LABORATORY PROCESS3. Abutment Milling (1/5) • Fix the abutment to the analog

  26. LABORATORY PROCESS3. Abutment Milling (2/5) • Abutment Milling (Step 1)

  27. LABORATORY PROCESS3. Abutment Milling (3/5) • Abutment Milling (Step 2)

  28. LABORATORY PROCESS3. Abutment Milling (4/5) • Abutment Milling (Step 3)

  29. LABORATORY PROCESS3. Abutment Milling (5/5) • Post Milling

  30. LABORATORY PROCESS4. Pattern Resin & Wax-Up (1/3)

  31. LABORATORY PROCESS4. Pattern Resin & Wax-Up (2/3) • Wax-up process (Steps 1 & 2)

  32. LABORATORY PROCESS4. Pattern Resin & Wax-Up (3/3) • Wax-up process (Steps 3 & 4)

  33. LABORATORY PROCESS5. Sprewing (1/2) • Sprewing (Step 1)

  34. LABORATORY PROCESS5. Sprewing (2/2) • Sprewing (Step 2)

  35. LABORATORY PROCESS6. Investment (1/2) • Investment (Step 1)

  36. LABORATORY PROCESS6. Investment (2/2) • Burn out (Step 3) • Investment (Step 2)

  37. LABORATORY PROCESS7. Casting • Cast and extract cast structure

  38. LABORATORY PROCESS8. Adaptation & Metal Trimming • Check cast structure for adaptation on master model

  39. LABORATORY PROCESS9. Finishing

  40. LABORATORY PROCESS10. Transfer Jig (1/2) • Make the transfer Jig

  41. LABORATORY PROCESS10. Transfer Jig (2/2) • Place the abutment(s) inside the oral cavity by using the transfer jig

More Related