1 / 33

LHC IRQ Cryostat Engineering Design Review March 12, 2001 T. Page - Fermilab

LHC IRQ Cryostat Engineering Design Review March 12, 2001 T. Page - Fermilab. Topics. Corrector Mounting Interconnect Design Q2A / Q2B Weld Test Results. Corrector Locations. Alignment Requirements. Corrector Displacement: 500 m m [0.0197 in] Corrector Roll: 5 mrad. Corrector alignment

shanae
Download Presentation

LHC IRQ Cryostat Engineering Design Review March 12, 2001 T. Page - Fermilab

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. LHC IRQ Cryostat Engineering Design ReviewMarch 12, 2001T. Page - Fermilab

  2. Topics • Corrector Mounting • Interconnect Design • Q2A / Q2B Weld Test Results T. Page

  3. Corrector Locations T. Page

  4. T. Page

  5. Alignment Requirements • Corrector Displacement: 500 mm [0.0197 in] • Corrector Roll: 5 mrad • Corrector alignment • Oversized holes in corrector flange to allow for adjustment. • Outside diameter of skin will be used for lateral alignment. • Dowel holes in coil / scribe line will be used for rotational alignment. T. Page

  6. Fermilab - MCBX Mounting (Q2A) • (3) MCBX Spacer • (Fermilab cold mass dia.=416mm) T. Page

  7. KEK - MCBX Mounting (Q1 & Q3) • (1) MCBX Mounting Ring • (KEK cold mass dia.=490mm) T. Page

  8. KEK - MQSXA Mounting (Q3) • (2) MQSXA Mounting Ring • (KEK cold mass dia.=490mm) T. Page

  9. KEK End Ring Design T. Page

  10. KEK Mounting Cross-Sections T. Page

  11. MCBX Shipping Restraint T. Page

  12. MCBX Shipping Restraint T. Page

  13. Interconnect Design • Vacuum sleeve • Pipes and bellows • Absorbers • Interconnect kit T. Page

  14. IC Q1-Q2 T. Page

  15. IC Q1-Q2 T. Page

  16. IC Q2-Q3 T. Page

  17. Interconnect pipe with integrated bellows T. Page

  18. Interconnect - Welded Joint T. Page

  19. Absorber Design • Two absorbers: • TAS 2: Q1-Q2A IC • TAS 3: Q2B-Q3 IC • Copper clamshell around beam tube. • Copper absorber cooled by 4.5K lines. • Suspended in interconnect by rails mounted to end domes. • Heat loads: • TAS 2 - 13.2 W total • TAS 3 - 15.8 W total T. Page

  20. Absorber: TAS 3 T. Page

  21. Absorber (Q3 end) T. Page

  22. Absorber (Q2B end) T. Page

  23. Absorber Cross-Sections T. Page

  24. Interconnect Kit • Contents: • Absorber (not shown) • Cold mass & heat exchanger pipes with bellows • Weld rings • Shield bridge • MLI (not shown) • Outer vacuum sleeve T. Page

  25. Q2P1-Feedbox IC T. Page

  26. Q2P1-Return IC T. Page

  27. Q2A / Q2B Weld Test T. Page

  28. Q2A-Q2B Interconnect T. Page

  29. Test Setup T. Page

  30. Interconnect Tube T. Page

  31. Test Setup Schematic T. Page

  32. Weld Test Results T. Page

  33. Weld Stripes • Able to move cold mass by as much as 0.008” T. Page

More Related