1 / 30

DOE Perspective on Advanced Energy Materials

DOE Perspective on Advanced Energy Materials. Robert Romanosky, Technology Manager National Energy Technology Laboratory. January 6, 2009. Materials Program Goals.

verda
Download Presentation

DOE Perspective on Advanced Energy Materials

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. DOE Perspective on Advanced Energy Materials Robert Romanosky, Technology Manager National Energy Technology Laboratory January 6, 2009

  2. Materials Program Goals • Development of a technology base in the synthesis, processing, life-cycle analysis, and performance characterization of advanced materials. • Development of new materials that have the potential to improve the performance and/or reduce the cost of existing power and non-power technologies. • Development of materials for new systems and capabilities. NETL_WVU_MATERIALS_MEETING_1/6/2009

  3. USC Boilers/Turbines Gasifier Advanced Turbines Fuel Cells Sensors Oxy-Firing Fossil Energy Key Material Research Areas NETL_WVU_MATERIALS_MEETING_1/6/2009

  4. Systems Integration System modeling Virtual Simulation Instrumentation Sensors & Controls Advanced Materials Ultra-Clean Energy Plant UltraSuperCritical Materials Advanced Alloys Gasification & Combustion Seals & Electrodes for Fuel Cells Thermal Barrier Coating for Turbines Improved Refractories for Gasifiers ODS Coatings Gas Stream Cleanup Devices NETL_WVU_MATERIALS_MEETING_1/6/2009

  5. Policy Goal Coal Technologies Gasification Combustion Seques- tration Environ- mental Fuel Cells Turbines & Engines Technology Platforms Heat Exchangers Air/Gas Heaters Gas Separation Particulate Control Vessel Liners Component Technology Turbine Blades/ Rotors/Pipes Castings Membranes Hot-Gas Filters Refractory Castables/ Bricks Adsorbents Functional Materials Materials Technology Coatings/ Protection Materials New Alloys Breakthrough Concepts Ultra Supercritical Materials Materials R&D Elements Joining Materials Design Modeling Mechanical Properties Materials Charac- terization Corrosion/ Erosion Studies Synthesis & Processing/ Fabrication Program Roadmap NETL_WVU_MATERIALS_MEETING_1/6/2009

  6. A Dash of Wolfram, A Pinch of Nickel Creation of New Materials NETL_WVU_MATERIALS_MEETING_1/6/2009

  7. Advanced Research Materials Program HIGH TEMPERATURE APPLICATIONS • New Alloys - To increase the temperature capability of alloys for use in specific components required for advanced power plants by understanding the relationships among composition, microstructure, and properties. • Functional Materials - To understand the special requirements of materials intended to function in specific conditions such as those encountered in hot gas filtration, gas separation, and fuel cell systems. • Breakthrough Materials - To explore routes for the development of materials with temperature/strength capabilities beyond those currently available. • Coatings & Protection of Materials - To develop the design, application, and performance criteria for coatings intended to protect materials from the high-temperature corrosive environments encountered in advanced fossil energy plants. • Ultra Supercritical Materials – To evaluate and develop materials technologies that allow the use of advanced steam cycles in coal-based power plants to operate at steam conditions of up to 760°C (1400°F) and 5,000 psi NETL_WVU_MATERIALS_MEETING_1/6/2009

  8. Advanced Combustion/Gasification Conditions Development • Extended alloy lifetimes through improved coating performance and composition optimization • Microstructure and properties of HVOF-sprayed Ni-50Cr coatings • High-temperature corrosion resistance of candidate FeAlCr coatings in low-NOx • environments • Aluminide coatings for power generation applications Evaluation Metallic Coatings for Structural Alloys • Includes rig testing • Includes field testing Coatings Clusters Development Evaluation • YSZ thermal barrier coatings by MOCVD • Modeling of CVD processing • Development of non-destructive evaluation methods for ceramic coatings • Materials issues for syngas turbines Ceramic/ Composite Coatings • Includes field testing Gasifier Refractory Linings Gas Turbine Components

  9. Advanced Steam Conditions Development • Advanced pressure-boundary materials • High creep-strength alloys (Special Metals • Effects of off-normal metallurgical conditions on performance of advanced ferritic steels • Steam turbine materials and corrosion • Materials for USC steam turbines (consortium) Evaluation High-temperature ‘Conventional’ Wrought Alloys • Fireside and steamside corrosion of alloys for USC plants • USC materials plant trials (B&W) • Improved metallic recuperator materials (Solar Turbines CRADA) • USC steam tubing consortium New Alloy Clusters Development Evaluation • Enabling the practical application of ODS-ferritic steels • Optimization of ODS-Fe3Al and MA956 alloy heat exchanger tubes • Control of defects and microstructure in ODS alloys • Cross-rolling/flow-forming of ODS alloy HX tubes ODS Alloys • In-plant corrosion probe tests of • Corrosion and joining of ODS FeCrAl alloys for very high -temperature heat exchangers • MA956 heat exchanger tubes Advanced Heat Exchangers/ Engines

  10. Gas Filtration/Separation/ Clean-up Development Processing • Gas sensors for fossil energy applications • Brazing technology for gas separation membranes: advances in air brazing • Development of inorganic membranes for hydrogen separation • Activated carbon composites for air separation • Metal membranes for hydrogen separation Ceramic Membranes/ Structures Functional Materials Clusters Development Evaluation • Low-chrome/chrome-free refractories for slagging gasifiers • Protection systems: corrosion-resistant coatings Refractories • field testing Gasifier Refractory Linings

  11. Concept Development Concept Development • ORNL-2D: Multiphase HT Alloys: Exploration of Laves-strengthened steels • ORNL-4A: Novel structures through controlled oxidation • ORNL-4C: Concepts for smart, protective high-temperature coatings • AMES-2: Optimizing processing of Mo-Si-B intermetallics through thermodynamic assessment of Mo-Si-B and related systems • UT-2A: Effects of W on the microstructures of TiAl-based intermetallics • WVU-2: Influence of impurities on ductility of Cr-based alloys and in-situ mechanical property measurement • ORNL-2I: Development of ultra-high temperature molybdenum borosilicides-See below • Multiphase HT Alloys: Exploration of Laves-strengthened steels • Novel structures through controlled oxidation • Concepts for smart, protective high-temperature coatings • Optimizing processing of Mo-Si-B intermetallics through thermodynamic assessment of Mo-Si-B and related systems • Effects of W on the microstructures of TiAl-based intermetallics • Influence of impurities on ductility of Cr-based alloys and in-situ mechanical property measurement • Development of ultra-high temperature molybdenum borosilicides-See below Enabling Technologies Enabling Technologies Strength/Env Resistance at T > Current Alloys Strength/Env Resistance at T > Current Alloys • AMES-3: New Processing Developments in Metallic Powders for Fossil Energy Applications • REMAXCO-5: Pilot facility for the production of • New Processing Developments in Metallic Powders for Fossil Energy Applications • Pilot facility for the production of silicon carbide fibrils Breakthrough Concepts Breakthrough Concepts Increased HT capability for ‘Conventional’ Wrought Alloys Increased HT capability for ‘Conventional’ Wrought Alloys Concept Development Concept Development Enabling Technologies Enabling Technologies • ORNL-2I: Strengthening phases with increased stability • Strengthening phases with increased stability • Interaction with ORNL-2C • Interaction with ORNL Advanced Combustion/Gasification Conditions Advanced Combustion/Gasification Conditions

  12. Materials Evaluation for Biomass and Black Liquor Gasifiers • Gasification of black liquor and biomass involves high-pressure, high-temperature, and sometimes caustic conditions. • Materials used in gasifier equipment must be robust and able to withstand the chemical and thermal conditions as well as the cycling aspects of gasifier operation • Critical materials issues such as fatigue, corrosion, stability, and longevity of materials will be the primary focus of research • Corrosion and corrosion fatigue studies will be conducted with the intent of identifying possible degradation mechanisms for metallic and refractory materials. NETL_WVU_MATERIALS_MEETING_1/6/2009

  13. Hydrogen Membranes • Hydrogen can be produced from coal, natural gas, biomass, and biomass derivatives through the use of gasification, pyrolysis, reforming and shift technologies. • The use of membranes holds the promise of reducing cost by combining the separation and purification with the shift reaction in a reactive separation operation. • Development is needed to improve hydrogen membrane separation and purification technology for use in the production of hydrogen • The focus of the research should be on low cost, high flux rate, durable membranes systems that can be integrated with the shift reaction. • Membranes of interest include ceramic ionic transport membranes, micro-porous membranes, and palladium based membranes. NETL_WVU_MATERIALS_MEETING_1/6/2009

  14. UltraSupercritical Boilers and Turbines • Current technology for USC Boilers • Typical subcritical = 540 °C • Typical supercritical = 593 °C • Most advanced supercritical = ~610 °C • USC Plant efficiency is improved to 45 to 47% HHV • Ultrasupercritical (USC) DOE goal for higher efficiency and much lower emissions, materials capable of: • 760 °C (1400 °F) • 5,000 psi • Oxygen firing • Meeting these targets requires: • The use of new materials • Novel uses of existing materials NETL_WVU_MATERIALS_MEETING_1/6/2009

  15. Technical Barriers • Long-term degradation of materials (100-300,000 hours) are not well understood or characterized for this alloy class • Combination of creep strength, weldability (necessary component for boiler fabrication), oxidation, and corrosion resistance • Effects of heat-treatment, fabrication variables, welding is critical • Need new welding processes, fabrication processes, etc. • Ability to produce material is also an issue Microhardness map of Thick Section USC weld showing “soft” weld metal – long-term testing is needed to understand the implication of this type of weld on material performance NETL_WVU_MATERIALS_MEETING_1/6/2009

  16. What and Why Oxy-fuel Combustion • Energy production (in particular, electricity) is expected to increase due to population increase and per capita increase in energy consumption • Oxy-fuel combustion is one option for providing increased capacity to satisfy the future energy consumption demand • Can be used for retrofitting or new plants • Global climate change - one of the sources for CO2 increase in the atmosphere is exhaust from fossil fuel combustion plants • Oxy-fuel combustion readily supports the capture and sequestration of CO2 from power plants NETL_WVU_MATERIALS_MEETING_1/6/2009

  17. Technological Barriers – Materials Needs • Better understanding of material performance in oxyfuel environments • Evaluate ash assisted hot-corrosion of boiler alloys • Develop computational models to predict fireside corrosion will aid in the development of all advanced combustion systems • Evaluate other plant components e.g., coal pulverizers (wear-corrosion interactions) • Future Capability: Combine Oxyfuel with USC. • Potential cleaner coal combustion technology • Oxyfuel: ease of flue gas clean-up and CO2 sequestration • USC: maximize efficiency • Need cost effective advanced alloys that can withstand the oxyfuel/USC environment • higher temperatures and higher pressures than current systems NETL_WVU_MATERIALS_MEETING_1/6/2009

  18. Signal Wire Sensor 1” Advanced Sensor Materials • Harsh Environmental Conditions • Sensor Material Development • Rugged Sensor Designs NETL_WVU_MATERIALS_MEETING_1/6/2009

  19. Driver for New Sensing Technology • Advanced Power Generation: • Harsh sensing conditions throughout plant • Monitoring needed with advanced instrumentation and sensor technology. • Existing instrumentation and sensing technology are inadequate • Coal Gasifiers and Combustions Turbines: • have the most extreme conditions • Gasifier temperatures may extend to 1600 °C and pressures above 800 psi. Slagging coal gasifiers are highly reducing, highly erosive and corrosive. • Combustion turbines have a highly oxidizing combustion atmosphere. • Targeting development of critical on line measurements • Sensor materials and designs are aimed at up to 1600 °C for temperature measurement and near 500 °C for micro gas sensors. • Goal is to enable the coordinated control of advanced power plants followed by improvement of a system’s reliability and availability and on line optimization of plant performance. NETL_WVU_MATERIALS_MEETING_1/6/2009

  20. Materials for Sensing in Harsh Environments(Optical and Micro Sensors) • Sapphire • Alumina • Silicon Carbide • Doped Silicon Carbide Nitride • Yttria stabilized zirconia • Fused/doped silica for certain conditions • Interest in • Active / doped coatings • 3D porous or “mesh” nano-derived ceramics / metal oxides NETL_WVU_MATERIALS_MEETING_1/6/2009

  21. Turbines • Technical Barriers • Environmental Conditions • Research Underway NETL_WVU_MATERIALS_MEETING_1/6/2009

  22. Gas Phase Conditions for Advanced Turbines IGCC Based Syngas and H2 Fueled Turbines IGCC Oxy-Fuel Turbine Cycle NETL_WVU_MATERIALS_MEETING_1/6/2009

  23. Turbine Materials Technical Barriers • Mechanical / chemical stability of bond coating interface • Stresses developed as a result of CTE mismatch • Change in thermal conductivity across the thickness of the ceramic as a result of service exposure • Cleanup techniques with various levels of sulfur removal: • MDEA: 20 – 30 (+) ppm • Selexol: 2 – 11 ppm • Rectisol: 0.01 – 6 ppm • CO2 capture w/ deeper sulfur removal w/ less sulfur problems • Research needed on: • new materials & deposition procedures (techniques) • new TBC structures with corrosion resistance • environmental barrier coating (EBC) • ceramic matrix composite (CMC) These number will tend towards the lower numbers NETL_WVU_MATERIALS_MEETING_1/6/2009

  24. What R&D is underway to address these issues? • TBC compositions for corrosion resistance with no increase in thermal conductivity and good CTE match. • TBC failure mechanisms with alternate fuels especially under high heat flux (HHF) conditions. • Understanding deposition (condensation) kinetics for critical vapor species on high temperature surfaces – water vapor activated recession of TBC materials • Effect of cooling strategy on TBC thermal gradient and degradation modes • Deposition, erosion, or corrosion (D-E-C) due to contaminants (Si, Al, Ca, Mg, Na K, sulfate ions, As, P, Se etc.) when firing syngas • Simulated lab tests NETL_WVU_MATERIALS_MEETING_1/6/2009

  25. Fuel Cells • Technical Barriers • Environmental Conditions • Research Underway NETL_WVU_MATERIALS_MEETING_1/6/2009

  26. Fuel Cell Materials • Material improvements process • Faster kinetics for oxygen reduction to lower the irreversible losses for electrochemical charge transfer. • Stable surface chemistries are sought with active sites for dissociative adsorption of oxygen • Technical barriers • Cathode performance correlated with oxide surface chemistry in high partial pressures of oxygen • Cathode surface boundary is affected by cation dopant distributions • Local surface chemistry establishes adsorption sites with kinetic barriers to charge and mass transport • Dopants and defect segregation modify surface chemistry • Modified atomic arrangements can provide stable and fast reaction sites with improved electrochemical performance NETL_WVU_MATERIALS_MEETING_1/6/2009

  27. Fuel Cell Materials • R&D Underway • Work to fully understand the surface chemistry of established cathode oxides • Epitaxial growth through pulsed laser deposition to prepare thin film model surfaces • Identify key correlations between surface structure, chemistry, and performance parameters • Theoretical modeling to interpret the underlying chemistry and guide modifications to the cathode surfaces. • Technology Future • Improve Cathode performance to extend functional operating temperature from the current lower range of 750 °C down to 650 °C. • Technology Benefit • Reduce SOFC cost through more efficient operational performance. • Increase efficiency in advanced power generation systems NETL_WVU_MATERIALS_MEETING_1/6/2009

  28. What Does the Future Look Like? • The USA and the world will face great energy challenges with ever increasing environmental constraints • Advanced fossil energy power systems will be needed • The Advanced Research Materials Program is poised to have even greater impacts on future energy systems • Novel materials for gas separation • Fuel cell materials • Next generation stainless steels with higher strength and better oxidation resistance • Advanced coatings • Prescriptive materials design and lifetime prediction for extreme environments NETL_WVU_MATERIALS_MEETING_1/6/2009

  29. USC Boilers/Turbines Gasifier Advanced Turbines Fuel Cells Sensors Oxy-Firing Fossil Energy Key Material Research Areas NETL_WVU_MATERIALS_MEETING_1/6/2009

  30. NETL_WVU_MATERIALS_MEETING_1/6/2009

More Related