IMRT Commissioning

1. Gary A. Ezzell., Ph.D. Mayo Clinic Scottsdale IMRT Commissioning

2. Welcome to Arizona

3. Commissioning elements Validating the dosimetry system Commissioning the delivery system Commissioning the planning/delivery systems for dosimetric accuracy Learning how to use IMRT

4. Step 0: the dosimetry system Decide on the system that will be used to measure dose distributions Determine the measurement uncertainty Compare measurements of unmodulated fields to ion chamber scans Needed to establish acceptance criteria

5. Delivery system tests Need to create test patterns independent of planning system Need to check MLC positioning accuracy MLC dynamic motion accuracy Effect of rounded leaf ends MU linearity ...

6. Radiation field �offset� for rounded leaf ends For rounded MLC leaf ends, there is an offset between the light and radiation field edges: ~0.6 mm Important in IMRT

7. Why important for IMRT?

8. Measuring the offset Irradiate a series of strips that abut Use different values of offset Select offset value that gives best uniformity

9. Measuring the offset

10. Measuring the offset

11. MLC accuracy Tenths of millimeters are important for IMRT Use patterns of abutting strips for a sensitive test Test at different gantry and collimator angles Select subset for routine QA

12. Abutments are very sensitive to positioning

13. DMLC tests For dynamic MLC motion, leaf speed and dose rate also need to be controlled Need to test for range of leaf speed and dose rates, as well as gantry and collimator angles Create patterns that move a 1 cm gap using all leaves at same or variable rates

14. Sweep all leaves at same rate

15. Sweep leaves at different rates

16. Special problem of matching accelerators In �99 Mayo Clinic Scottsdale had two �matched� Varian 2100C linacs, but IMRT doses differed by ~2.5% Needed to adjust MLC calibration on one machine by 0.13 mm

17. Delivery system QA Sweep a 5mm gap across a 10 cm span with Farmer chamber at center Take ratio to 10x10 open field 2.5% for 0.2 mm change

18. Routine QA checks for positioning accuracy Abutment films 1 mm gap films Check at different gantry, collimator angles Check frequency(?)

19. �and now for a change

20. Planning system: Dosimetric accuracy For IMRT, the MLC leaves move through the area of interest Final distribution is created by summing many beamlets New things become important Leakage through MLC leaves Penumbra defined by MLC leaves Small fields

21. MLC leakage - measure average value Leakage through leaf (~2%) Between neighboring leaves (~5%) Measure using a pattern that fully closes all leaves - careful not to be under carriage or jaw

22. Penumbra Measure with film, diode, or microchamber, conventional scanning chamber too wide Subtle effects make a difference in IMRT

23. Dosimetric validation (1) Start with the basics Define simple open fields irradiating a simple phantom check calculated output, PDD, profiles against standard measurements (just like commissioning any planning system) And shaped static fields also

26. Dosimetric validation (2) Define simply-modulated fields with wide regions that can be measured with chamber and film (or equivalent) Check: Leakage/transmission Basic modulation Penumbra Out of field dose

27. �Leak100� � �Leak0� patterns

28. �Ridge� and �Trench� patterns

32. �Band100� � �Band0� patterns

33. Finally, highly modulated single fields

34. What to do about differences? May need to adjust the beam model May need to live with it That is, take known deficiencies into account when evaluating plans Very important to know about it, especially for critical structures

35. And once you are over the simple stuff �

36. Dosimetric validation (3) Define targets and structures in a simple phantom: mock clinical situations Create inverse plan Measure doses with chamber, film, � Evaluate dose/MU in low gradient region Evaluate isodoses on many planes

37. Mock prostate

40. Mock Head/Neck

43. Mock spine

47. Dosimetric evaluation of mock clinical plans What kind of agreement to expect in high dose, low gradient regions? ~2 - 4% is reasonable (chamber) What kind of agreement to expect for isodoses? Much harder to specify ~2 - 4 mm for 50% - 90% lines

48. How to be more quantitative? Acceptance criteria should be stated statistically, such as: �within the region of interest, 95% of the calculation points should agree with the measurement to within 5%, which combines the desired degree of agreement with reality (3%) with the two-sigma uncertainty in the measurement technique (4%).�

49. What is the region of interest? What is the desired degree of agreement with reality? What is the uncertainty in the measurement technique? What percentage of the points should agree to the specified tolerance? Questions

50. Questions For the points that do not agree to that tolerance, is there an outer limit of acceptability? Should the agreement be expressed as a percent of the local dose, prescription dose, or some other dose? Should distance to agreement be incorporated?

51. Another question What is the role of quantitative assessment of individual IMRT fields vs. composite doses?

52. Dosimetric validation (4) Test calculations in the presence of inhomogeneities

55. Dosimetric validation - Summary Know your measurement uncertainties Start with simple situations that can be more easily analyzed Design tests that focus on specific parameters, e.g. Transmission Small or narrow fields Penumbra and dose outside field

56. Finding your way around �

57. General principles (1) Don�t ask for the impossible If you ask for NO dose to the cord, 60 Gy may appear just as bad as 40 Gy to the optimizer Look at a good 3D conformal alternative to get a starting point

58. General principles (2) Explain the problem sufficiently to the system Define what needs to be treated Define what needs to be avoided The system is going to choose the beam shapes according to the structures defined

59. General principles (3) Define the problem sufficiently to the human who is doing the planning What is absolutely necessary What is desirable Where you are able to compromise

60. General principles (4) Understand the difference between three kinds of �prescriptions�: What you want and tell the human planner to get What the planner tells the system to try for What you eventually get and treat with

61. General principles (5) Learn what �knobs� there are DVH criteria for targets and structures Relative weights or tissue types Number of intensity levels Number and direction of beams � Try each individually and systematically on idealized and actual patients

62. General principles (6) Dose uniformity vs Conformality Target dose uniformity can be expected to decrease with increasing concavity increasing dose gradient decreasing number of beams

63. General principles (7) Don�t assume IMRT is the way to go 3D conformal, judged by the same criteria, may be better parallel-opposed beam pairs are often best IMRT system may have limitations 1x1 beamlets insufficient weight to dose uniformity

64. Building experience with artificial problems Designed to illustrate performance for certain types of situations Observe how changing various planning parameters affects plan quality and delivery efficiency For each, decide on relevant measures of plan quality

65. Simple cylindrical geometry Single target with 1 cm PTV expansion (PTV is 8 cm diam, 8 cm long) Goal: target dose uniformity PTV max/min PTV D2/D98 Compare to: 3 open fields evenly weighted

66. Target dose uniformity As you vary the requested degree of target dose uniformity, how do the results change?

67. Goal: target uniformity(Corvus V5)

68. Simple cylinder with 4 structuresPipesEasy Goal: structure sparing vs target uniformity PTV D2/D98 Structure mean/PTV mean 15 fields equispaced Try different structure goals 50, 20, 10, 2% of target dose

69. PipesEasy: Effect of changing structure goals

70. PipesEasy: Effect of changing structure goals

71. PipesEasy: comments Asking for too much sparing degrades target uniformity with little improvement

72. What is achievable? Limiting dose gradient

73. C Shape Goal: structure sparing vs target uniformity PTV D2/D98 Structure D5/PTV 98 15 fields equispaced Try different structure goals 60, 50, �, 10% of target dose

76. Limiting dose gradient

77. Buildup Expand PTV by 2-10 mm Evaluate dose uniformity CTV max/min Volume max/CTV mean

79. Comments on these artificial problems Good for gaining some feel for the �knobs� for the limiting conditions (e.g. maximum dose gradients) for the consequences of being unrealistic in the problem statement

80. Dealing with real clinical plans Determine method/conventions for defining structures and targets Determine margins (CTV and PTV)

81. Dealing with real clinical plans Decide on criteria for an acceptable plan e.g. PTV dose must be sufficiently uniform: PTV D2/D98 ? 1.15 Decide on parameter to be optimized e.g. minimize mean parotid dose

82. Dealing with real clinical plans Start with a 3D conformal plan to get a sense of what is achievable Use these results as a starting point for DVH goals for the inverse planner Start with relaxed goals and gradually tighten them

83. Welcome to Arizona � and IMRT