1 / 24

Oxyacetylene Welding

Oxyacetylene Welding. By Matt Scott. Introduction. OAW is a welding process that heats the base metal with a controlled mixture of acetylene and oxygen gas. The heat from the torch allows for the melting and mixing of the base metal and filler metal to form a solid weld.

cedric-craig
Download Presentation

Oxyacetylene Welding

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Oxyacetylene Welding By Matt Scott

  2. Introduction • OAW is a welding process that heats the base metal with a controlled mixture of acetylene and oxygen gas. The heat from the torch allows for the melting and mixing of the base metal and filler metal to form a solid weld.

  3. 8 Steps to Making a Quality Weld • Safety Check • Select a tip based on metal thickness • Adjust gas pressures • Ensure the tip is clean • Set torch to neutral flame • Get Comfortable • Maintain a consistent Coupling Distance • Oscillate torch to ensure fusion.

  4. Step 1 – Safety • At a Glance • Stop – smell, look and listen before using! • Did you ensure the cylinders where chained up and hoses where in good shape? • Did you scan the whole system to see if there was anything odd? • SAFETY FIRST!!!!!!!!!

  5. Step 2 and 3 – TIP Selection & Setting the Gas Pressure Victor Cutting Equipment

  6. Step 4 – Ensure the Tip is Clean • Indicators of a clean tip are: • Preheat flame is sharp and ¼” in length. • Secondary flame does not splinter

  7. Step 5 - Set torch to Neutral Flame • A neutral flame is when you have the same ratio of acetylene and oxygen burning • Most efficient welding flame setting • Flame temperature is 5800 Fahrenheit

  8. Step 6 – Get Comfortable • Steady yourself when welding

  9. Mild Steel Welds • Oxyacetylene welding is limited to thin metal sections or when portability is important • Today almost exclusively used on thin metal • An electric arc welding processes is usually used for welding thicker metal

  10. Mild Steel Welds • Easiest metal to gas weld • Welds with 100% integrity possible • Secondary flame shields the molten weld pool from the air • Atmospheric oxygen combines with carbon monoxide to produce carbon dioxide • Carbon dioxide forces surrounding atmosphere away from the weld

  11. Factors Affecting the Weld • The torch tip size controls the weld bead width, penetration, and speed • Torch angle and the angle between the inner cone and the metal effect: • Speed of melting • Size of the molten weld pool • Welding rod size and torch manipulation control the weld bead characteristics

  12. Step 7&8 Coupling Distance and Torch Manipulation “Flashing” the flame off the metal will allow the molten weld pool to cool and reduce in size.

  13. If the buildup on both welds is removed, weld (B) would be stronger

  14. Characteristics of the Weld • Molten weld pool must be protected by the secondary flame • Weld crater susceptible to cracking • Number of sparks in the air increases just before a burn through • Burnout does not happen to molten metal until it reaches the kindling temperature

  15. Outside Corner Joint • Flat outside corner joint made with or without filler metal • One of the easiest welded joints to make • Filler metal not needed if sheets are tacked properly • Filler metal is added uniformly

  16. Lap Joint • Flatlap jointeasily welded with basic manipulations • Use caution when heating the two sheets • Both sheets start melting at the same time • Direct the flame on the bottom sheet away from top sheet • Filler rod added to the top sheet • Gravity pulls the molten weld pool down

  17. Tee Joint • Flat tee joint is difficult because the Uneven heating • Large percentage of welding heat is reflected back on the torch • Angle the torch in the direction of weld travel (push technique) • Adjust the flame to be somewhat oxidizing • Keep a tight coupling distance to focus heat at the root.

  18. Out-of-position Welding • Welds performed in position other than flat • The following welds are out of position: • Vertical • Horizontal • Overhead • Somewhat more difficult than flat welds

  19. Common OAW Vocabulary • Base Metal • Weld Metal • Filler Metal • Toe and Crater of weld • Delivery Pressure vs. Working Pressure • Flashback vs. Backfire • Oxygen vs. Air

  20. Summary • Learning to control the heat input to the weld by changing the torch angle, height, or travel speed is important • Oxyacetylene welding is the process of preference for thin materials • The most common problem with OFW welding is heat and weld distortion

  21. Where to Get More Information • Owners Manual • Welding Principles and Applications by Larry Jeffus • PCC Welding

More Related