1 / 22

LCLS Energy Jitter Status in 2012

LCLS Energy Jitter Status in 2012. Franz-Josef Decker 24-Oct-2012 thanks to: J. Turner, R. Akre, J. Craft, A . Krasnykh, M. Nguyen, W. Colocho, … for helping to reduce jitter over the years. Outline. History of L1S jitter

chiara
Download Presentation

LCLS Energy Jitter Status in 2012

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. LCLS Energy Jitter Status in 2012 Franz-Josef Decker 24-Oct-2012 thanks to: J. Turner, R. Akre, J. Craft, A. Krasnykh, M. Nguyen, W. Colocho, … for helping to reduce jitter over the years

  2. Outline LCLS Jitter Status in 2012 • History of L1S jitter • How does a high voltage change of L1S modulator propagate • History of DL2 energy jitter (or different energies, peak currents) • Jitter is 120% (high E) to 250% (low E) of energy spread [0.04–0.12%] • What is needed for seeding • Different techniques to localize and quantify jitter

  3. L1S phase jitter over the years • 0.35 deg to 0.03 deg Un-SLEDed, HV=340kV ? Sample images BC1: E =250 MeV HV=300kV LCLS Jitter Status in 2012

  4. L1S Phase and Amplitude Calibration vs. High Voltage Phase -22 deg and Amplitude +145 MeV(BC1: E = 250 MeV)5.0 deg / % voltage change 2.5 MeV / % voltage change [expected: 5.2 deg, 1.74 MeV(sqrt 2?)] 0.1%  0.5 deg, 0.25 MeV Now at -25.5 deg, 115 MeV gives: E= 103.79 MeV 104.45 MeV +0.66 MeV [0.42 (phase) + 0.24 (ampl)]0.66/220 = 0.3% more energy in BC1 R56 = -45.5 mm  -0.468 deg in L2 -36 deg  -35.53 deg: 5 GeV  4.97 GeV-0.57 % (less energy) [R56 = -24.7 mm  +0.483 deg or 0.015 deg in L3, (L2 phase can be compensated with +18 deg in L3)] DV/V = 100 PPM (0.05 deg)  0.057% at 5 GeV LCLS Jitter Status in 2012

  5. Expected vsMeasured Slope BC2 Evs BC1 E Expected: -0.57 / 0.3 = -1.9 Measured: -0.841/0.38 = -2.210.16 corrcoef = rho LCLS Jitter Status in 2012

  6. DL2 Energy vs BC2 Energy Expected: 5 GeV / 12.3 GeV = 41% Measured: 36% / 0.744 = 48% [ = 0.044% / 0.091%] (peak current increases jitter 20%) [over-compression reduces jitter] LCLS Jitter Status in 2012

  7. Energy Jitter History at DL2 0.12 % at 3.5 GeV 3.0 times 0.04 % at 13.5 GeV 3.85 times LCLS Jitter Status in 2012

  8. Effect of Peak Current Best energy jitter 0.03 %, long bunch, high energy LCLS Jitter Status in 2012

  9. LTU WireDE/E Good: 0.033 % ‘+’ 0.040 % = 0.052 % 12.3 GeV Hard X-ray 3.5 GeV Soft X-ray Jitter 0.051 % 140 % 0.037 % = 0.063 % Jitter 0.118 % 250 % 0.046 % = 0.127 % LCLS Jitter Status in 2012

  10. How does the Energy Jitter Influence Seeding? Intensity on Direct Imager after Simulation: Jitter paints the KMONO [SASE: 0.07%] vs LTU x distribution 0.052/1.25 = 0.042% [seeded sometimes 0.030%  /2] LCLS Jitter Status in 2012

  11. Average Intensity and Variation, Seeded after KMONO 70% for 0.042% energy jitter, variation 40% rms 90% for 0.020% energy jitter, variation 10% rms 2* • 0.020% energy jitter requires DV/V = 80 PPM or 0.04 at L1S • [= 0.020/1.2*13.6/5 / 0.057 *100 PPM] LCLS Jitter Status in 2012

  12. L1S phase is still the worst offender of energy jitter [12% of jitter power at 120 Hz,] but 35% at 60 Hz But other devices are close by: 60 Hz 120 Hz L1S L1S 24-1 L0A 27-3 30-7 29-1 L0B 27-5 25-4 27-7 29-1 LCLS Jitter Status in 2012

  13. Main Causes of L1S Jitter • RF: • Multi-pacting in load and reflecting back up and DOWN • Single pulse break down (?) Both avoided by going un_SLEDed (after 220 MeV in BC1) • Modulator HV: • Thyratron not switching off “cleanly”, affecting next pulse Avoid by going to 300 kV (costs ~30 MeV, 190 MeV in BC1?) or MANY other approaches LCLS Jitter Status in 2012

  14. L1S Modulator Modifications over the Years Try to “match” modulator to klystron impedance (high micro-perveance helps) Change klystron and a few thyratrons, and ranging them Run at 300 kV instead of 340 kV Shorter PFN Tail end clipper “Mystery fan” Delay charging PFN after thyratron firing [ended in fire 120Hz] Measuring and correcting HV (ala SCALA) going on now Other ideas: capacitors with lower inductance … LCLS Jitter Status in 2012

  15. Techniques to Localize and Quantify Jitter • Methods to get data: • BSA (Beam Synchronous Acquisition) • Correlation plot • get_wf (waveforms) • L1S_jit (Jitter vs time) • Jitter CUD, FTP from matlab, • LLRFgui, KLYSTRONgui, … • Analyzing data: • BSA_jitter_fft (FFT, corrcoef, slope, …), …svd • corr_jitt … • get_wf_an14 • Plot History … LCLS Jitter Status in 2012

  16. BSA Data (Power Spectrum in DL2 Energy BPM) Feedback on: 0.054% Feedback off: 0.043 % (even with big 60 Hz component, without 0.040%) LCLS Jitter Status in 2012

  17. Correlation Plot and BSA [Transverse and FEL Intensity] BPM:IN20:371:Y is 75% correlated with VCC x position So laser causes at least 56% (=0.75^2) of 371 Y jitter (Is 42 Hz coming from laser OR MCOR power supply?)  5 Hz data From injector laser ? LCLS Jitter Status in 2012

  18. Jitter from Waveforms, e.g. L1S 300 raw waveforms, with RMS*1000 (red) revealing some elevated jitter inside the pulse, reflected signals show early multi-pacting Insert Presentation Title in Slide Master

  19. DL2 and BC1 Pie Charts Much of DL1 explained “Rest” of BC1 is big (maybe 60 Hz shows more), Laser_P is big, but gets compressed, BUT FBs sees it LCLS Jitter Status in 2012

  20. Localize Jitter vsz Concentrate on source: 16.7 Hz Make IFFT of FFT-data with only that frequency, then plot max-min vsz, fit oscillation BPM_pvs(100) = 'BPMS:BSY0:61' LCLS Jitter Status in 2012

  21. SVD for 1st BPM in DL2 L0A_A L0B_A last pulse missing, not used 60 Hz  DL2  BC2 L0B_A L0A_A L0B_A last pulse missing, not used L0A_A L0B_A MDL 476 Thales Ref Insert Presentation Title in Slide Master

  22. Summary • L1S makes ~36% of DL2 energy jitter power: • 0.6^2 + 0.8^2 = 0.36 + 0.64 = 1.0 • Energy jitter is 0.04% for hard x-ray, 0.12% for soft [0.18%] • Lowering BC1 energy to 190 MeV, might avoid current • modulator instability • Hard seeding need about 0.02%, [soft seeding ?] • Presented different methods to track down and quantify • jitter LCLS Jitter Status in 2012

More Related