1 / 22

Engineering Low-Head Dams for Function and Safety

Engineering Low-Head Dams for Function and Safety. Fritz R. Fiedler Department of Civil Engineering University of Idaho. What is a Low-Head Dam?. A dam that is typically less than 15 feet tall Used to pond water behind them but not control flow

judd
Download Presentation

Engineering Low-Head Dams for Function and Safety

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Engineering Low-Head Dams for Function and Safety Fritz R. Fiedler Department of Civil Engineering University of Idaho

  2. What is a Low-Head Dam? • A dam that is typically less than 15 feet tall • Used to pond water behind them but not control flow • Head: a term that refers to elevation, which can be related to fluid pressure and energy

  3. Why are they dangerous? • Low-head dams cause water to recirculate, thus trapping buoyant objects

  4. y V w Flow in rectangular channels • Side view • Front view Variables: y = flow depth (L) w = channel width (L) A = flow area = yw (L2) V = flow velocity (L/T) Q = discharge = VA (L3/T) q = Q/w (L2/T) Example: y = 2 ft w = 1.5 ft A = 3 ft2 V = 3 ft/s Q = 9 ft3/s q = 6 ft2/s Q

  5. States of flow in open channels • For a given Q, flow in open channels can be subcritical, supercritical, or critical • Subcritical: disturbances on water surface will travel upstream (flow velocity less than wave velocity); high y, low V • Supercritical: disturbances will not travel upstream (flow velocity greater than wave velocity); low y, high V • Critical: flow velocity equals wave velocity

  6. Hydraulic Jump Hydraulic Jump 2 Q = V1A1 = V1y1w 1 Q = V2A2 = V2y2w Image source: http://www.engineering.usu.edu/classes/cee/3500/openchannel.htm Note: Q is constant, so V1y1 = V2y2 (if w constant also)

  7. Froude Number • Ratio of inertia forces to gravity forces • F = V / (gy)0.5 • G = gravitational acceleration • Subcritical flow: F < 1 (gravity forces larger) • Supercritical flow: F > 1 (inertia forces larger) • Critical flow: F = 1

  8. Froude Number Hydraulic Jump 2 1 F1 = V1 / (gy1)0.5 F1 > 1 F2 = V2 / (gy2)0.5 F2 < 1 Image source: http://www.engineering.usu.edu/classes/cee/3500/openchannel.htm

  9. Initial and Sequent Depths • Relationship between depths before (initial) and after (sequent) a hydraulic jump • If y1 and V1 are known, can compute y2

  10. Flow over a dam (weir) As water flows over dam, goes through critical depth, yc at which F = 1 subcritical H yc Hydraulic Jump y0 subcritical P supercritical y1 y2 Q = CwH1.5 or q = CH1.5 where C is a weir coefficient that varies with dam type and H – but we are going to find and measure yc

  11. Critical Flow • At critical flow, F = 1 = Vc / (gyc)0.5 • Vc = (gyc)0.5 • Measure yc at dam, compute Vc then • Q = Vcycw • How is the location of yc found?

  12. Submerged Hydraulic Jump H yc y0 P y1 y2 yt • When yt exceeds y2 the jump becomes submerged • Degree of Submergence = S = (yt – y2) / y2 • When S < 0, jump occurs downstream • When S > 0, jump is submerged • If yt becomes large enough, dam will be submerged too • In the flume, we can control yt

  13. waves travel up waves travel down H yc y0 Dy P y1 y2 yt

  14. Project Steps • Analysis • Measure variables at two discharges • With and without tailwater submergence • Design • Objectives: maintain upstream depth, allow safe passage, create surf wave, minimize cost • Method: simple calculations, physical model studies and testing

  15. Analysis • At low discharge • With no tailwater • Measure: H, P (dam height), yc (must locate), y1, y2, Dy • Compute: Vc, Q, q, F1, C • Evaluate: measurement accuracy, sequent depth equation, floating object passage • With tailwater submerging jump • Measure: yt, Dy, and compute S • Evaluate: measurements, floating object passage • Repeat 1., a., b., … for high discharge

  16. Notes • We can mark, with tape and markers, the water levels right on the flume • Mark the height of the tailwater gate • We will keep flume slope, discharges constant throughout semester • Group Assignment: create a data sheet based on previous slide before next class.

  17. Design • Conceptual • What makes the hydraulic dangerous? • Uniformity, Dy, reverse flow velocity, aeration • How can this knowledge be used to meet objectives? • Analytical / Mathematical • Difficult! • Computer models • Simple equations (e.g., V-notch weir) • Physical models…

  18. Physical Models Image source: http://www.usbr.gov/pmts/hydraulics_lab/about/index.html

  19. Physical Model Testing • Measure variables as in Analysis (and more?) • What has changed? • Compare upstream pool elevations • Aim for little or no difference at both discharges • Test object passage • Surf spot? • Describe the hydraulic • Iterative process! (a.k.a., trial and error)

  20. Practicality and Economics • What types of materials would be required to build your design? (concrete, rip rap, …) • How and when could it be constructed? • If volume of material added is the primary cost, and the cost of this material per unit volume is known – how much would it cost? • Minimum volume = minimum cost: estimate the volume change in your design

  21. Other (Important) Considerations • Water Quality • Sediment and contaminants • Physical • Sediment and stream morphology • Dissolved oxygen • flooding • Ecological • Fish passage • Effects on aquatic life

More Related