1 / 15

PMD 101

PMD 101. Frank Effenberger Huawei Technologies. Introduction. Two issues involve the interaction of PMD speed and sensitivity FEC link rate increase Dual rate OLT receivers This presentation is meant to describe, in a simple way, the basic design of PMDs

manjit
Download Presentation

PMD 101

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. PMD 101 Frank Effenberger Huawei Technologies

  2. Introduction • Two issues involve the interaction of PMD speed and sensitivity • FEC link rate increase • Dual rate OLT receivers • This presentation is meant to describe, in a simple way, the basic design of PMDs • This should allow the membership to make educated judgments when choosing alternatives that impact speed/sensitivity

  3. Photodetectors • PIN diode • Responsivity (A/W) • Dark current (nA) • Intrinsic capacitance (pF) • Transit time (ps) • APD • All the above, plus… • Gain () • Excess Noise Factor ()

  4. Noise, and the first amplifier • There are several noise sources • RIN noise (from the transmitter) • Shot noise (from signal and dark current) • Excess noise (from avalanche gain process) • Thermal noise (from the circuit itself) • In PIN receivers, thermal noise dominates • In APDs, shot and excess noise play a role • The SNR out of the first amplifier tells the story in any (properly designed) circuit

  5. Trans-Impedance Amplifier • All modern optical PMDs use this topology • The key idea is that the amplifier’s gain reduces the effective impedance as regards the speed of response • Thus, a higher impedance value can be used (better SNR) while maintaining a high response speed (faster)

  6. _ + Circuit Vb R C Ip B2 = final LPF A Vout

  7. Signal to Noise Ratio • When thermal noise limited, • SNR ~ Ps2R/B2 ~ (Ps/B1) (Ps/B2) • For a fixed SNR: Ps~(B1B2)1/2 • When shot noise limited, • SNR ~ Ps/B2 • For a fixed SNR: Ps~B2

  8. The dual-rate problem • Signals come in at different rates • OLT must either • Parallel process signal at both speeds (and decide later which was right), or • Serially process signals at one speed • This decision has to do with choice of detector technology, and whether we are thermal noise limited or shot noise limited

  9. _ + Parallel PMD Circuit Vb R C 1Gb/s Signal 10 Gb/s signal Ip B21 = 1 GHz LPF A B22 = 8 GHz LPF Thermal-limited: Shot-limited:

  10. _ + Serial PMD Circuit Vb Control signal R2 R1 C 1Gb/s Signal 10 Gb/s signal Ip B21 = 1 GHz LPF A B22 = 8 GHz LPF Thermal-limited: Shot-limited:

  11. Comparison of Serial and Parallel • In shot-limited case, there is no difference • Pre-amp circuit does not impact SNR • In thermal-limited case, the Parallel circuit 1G SNR is degraded by factor B1/B12 = 8 • Constant SNR power penalty = 4.5 dB • Practical APD receivers fall midway between these two extremes • Avalanche multiplication factor optimized around M=10

  12. Optimized APD Gain

  13. Serial and Parallelwith optimized APDs • For an optimized APD: • SNR~ Ps4/3 / (B11/3B2) • For a fixed SNR: Ps~ (B1B23)1/4 • The Parallel circuit 1G SNR is degraded by (B1/B12)1/3= 2 • Constant SNR power penalty = 2.25 dB

  14. Overall Conclusions • Dual rate optics present us with a choice: • Implement the ‘serial’ circuit approach • No sensitivity penalty • Complexity of transimpedance control • Implement the ‘parallel’ circuit approach • Simpler transimpedance amplifier • Approximately 2~3 dB sensitivity penalty (APD) or 4.5dB penalty (pin)

  15. Sensitivity versus Speed (FEC) • For a normal receiver, B1=B2=B • We can see that SNR=f(P/B) for a receiver with an optimized pre-amp • So, a 0.28 dB increase in speed will require a 0.28 dB increase in received power for a constant SNR

More Related