180 likes | 184 Views
This notice outlines guidelines for conduct at meetings, prohibiting discussion of certain topics in order to comply with anti-trust laws. Participants are advised to make independent decisions without engaging in concerted actions.
E N D
Welcome Presented by: Arthur Harris
The Fine Print… Anti-Trust Guidelines: Please be advised that at any and all meetings, the following guidelines for conduct shall be established and followed: No participant shall be allowed to discuss any subject relating to prices charged, discounts offered of any nature, hourly rate, employee benefits, or agreements made with third party entities. Should any discussion of these items take place, said participant will be asked to refrain immediately, disregarding any pursuant discussion, and should said party deny such request, the meeting will be immediately disbanded. All Participants are herewith notified that the materials presented herein are not to be construed as information or direction to take concerted actions. Information can be utilized by individuals acting within their on judgment, making sound business decisions, without agreements with other participants of this meeting. This notice is hereby understood by all participants with regard to the laws governing this conduct. www.degweb.org
Alphabet soup www.degweb.org
So what is the DEG?? The Database Enhancement Gateway, or DEG, is designed to provide YOU, the estimating data “end user,” a place to provide proactive feedback to those who develop and provide the information we use. www.degweb.org
So what is the DEG?? And how does it work? www.degweb.org
Inquiry Examples 2010 Ford Escape - 4906 Area VehicleFRT END Part NameLT LOWER RAIL ASSY Part Number8L8Z7810009A Issue SummaryRail pays 7.5 hours. Has 196 welds. The part comes with part of floor and requires a lot of drilling out to remove the 196 welds. Removing interior, carpet, seats etc for where part welds to floor - removing gas lines, firewall insulator, etc.Number Welds196Suggested ActionIncrease labor time to 11.0 + hours Resolution After review, the following changes have been made:1. The estimated work time applied to the Lower Rail Assembly has been adjusted to 11.0 hours from 7.5 hours.2. The estimated work time applied to the “R&R apron/lower rail as an assembly” operation has been adjusted to 14.5 hours from 11.5 hours.3. Please note that these operations have a labor footnote applied that states, “LABOR: Time is after all necessary bolted-on parts are removed.” Audatex - 4818 Area VehicleUnder hoodMissing Part NameRefrigerant HoseDescriptionhigh side hose-condenser to evapIssue SummaryThe database is saying .3 and it just seems half of what it should be could you please let me know Resolution We have reviewed your inquiry and the labor for A/C lines is described as follows:A/C line labor consists only of the basic connect and disconnect of the line. The Audatex labor does not account for additional tasks that may be needed for the actual placement of the line through the vehicle. Most manufacturers do not offer a service procedure for this operation and the vehicles can differ depending on options and drive trains. The actual placement of the lines remain an estimate on sight operation using a manual entry. www.degweb.org
Inquiry Examples 2016 Jeep Cherokee 9757 Area VehicleLiftgate GlassSection5_PartNameLiftgate Glass deep tintSection5_IssueSummaryRear lift gate glass used to be bolt on older model. New model is now urethane type. Labor time appears to still be for bolt in (.8).Section5_ActualTime2.5 Resolution: Proposed Resolution: MOTOR stated:After review of the Lift Gate group, the following changes have been made:• In the Glass subgroup, the estimated work time applied to the Lift Glass has been updated to 2.5 hours from 0.8 hours.• An Add If Required operation has been added to the headnotes for R&R lift gate – add for transfer glass with an estimated work time of 0.9 hours. Correct labor time to urethane in Vs. bolted on to gate. 2016 Subaru Legacy- 9911 WE ARE REPLACING THE LT 1/4, LT TAIL LIGHT POCKET & REAR BODY PANEL. THE POCKET HAS A LISTED TIME IN THE DATABASE AS 2.5 HOURS BUT IN THE ESTIMATE IT COMES UP AS INCL AND IT DEDUCTS AN 1.0 OVERLAP. ACCORDING TO THE GUIDE, THE TAIL LIGHT POCKET DOES NOT SHOW INCLUDED IN EITHER PANEL. (REAR BODY & 1/4) ACTUALLY, IT DOESN\'T SHOW AT ALL; INCL OR DOES NOT INCLUDE. THE WAY IT LOOKS ON THE ESTIMATE, ITS LIKE WE ARE PAYING AN 1.0 TO INSTALL A PANEL!! Resolution Proposed Resolution: Updated the database not to show Tail Lamp Pockets included with Sectioning Quarter Panel. www.degweb.org
Where to Start? www.degweb.org
Are you “Book” Smart? Or More Importantly, Do You Understand Your Estimating System and Database Labor? www.degweb.org
CCC Information Services (CCC One) www.degweb.org
Getting Started!! www.degweb.org
Getting Started!! You are now ready to go online and fill out your inquiry. Let’s take a look at the Inquiry template www.degweb.org
Did you DEG Today? The fact of the matter is it requires you and your business to commit yourself to being involved and making a difference. How many estimates do you write a day? How many could you submit just one inquiry for? We all like to talk about how we would like things to be better. Let’s stop talking, and start making it better. The tool is here, are you going to use it? www.degweb.org
www.showmemore... So let’s take a moment to look at the website… www.degweb.org
Don’t be shy The Database Enhancement Gateway PO Box 615, Penfield, NY 14526 (302) 423-0207 (302) 450-7214 Fax DEG Administration: Arthur Harrisadmin@degweb.org