1 / 55

HYGIENE MANAGEMENT HYGIENIC DESIGN OF MACHINERY AND ESTABLISHMENT

HYGIENE MANAGEMENT HYGIENIC DESIGN OF MACHINERY AND ESTABLISHMENT. June 2002. Hygienic design. AIMS: KNOW THE IMPORTANCE OF A GOOD DESIGN OF BUILDINGS FACILITIES AND MACHINERY KNOW THE ASPECTS TO HAVE IN ACCOUNT KNOW ALTERNATIVES OF DESIGN AND HYGIENIC MATERIALS.

sereno
Download Presentation

HYGIENE MANAGEMENT HYGIENIC DESIGN OF MACHINERY AND ESTABLISHMENT

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. HYGIENE MANAGEMENT HYGIENIC DESIGN OF MACHINERY AND ESTABLISHMENT June 2002

  2. Hygienic design • AIMS: • KNOW THE IMPORTANCE OF A GOOD DESIGN OF BUILDINGS FACILITIES AND MACHINERY • KNOW THE ASPECTS TO HAVE IN ACCOUNT • KNOW ALTERNATIVES OF DESIGN AND HYGIENIC MATERIALS

  3. Attention to good hygienic design and construction, appropriate location, and the provision of adequate facilities, is necessary to enable hazards to be effectively contolled

  4. Index: • Plant site and location • Design and layout • Condition of floor • Condition of walls, doors and windows • Condition of ceiling and lights • Condition of drainage • Condition of other elements • Sanitary facilities • Equipment and utensils

  5. Plant site and location • The establishments shall be free from any hazards for the safety of the products. It should be located in areas which are free from objectionable odours, smoke, dust or other contaminants • The grounds and surrounding areas shall be tidy and free from improperly stored equipment, garbage, refuse, scrap metal (to avoid pest hiding and breeding) • Perimeter roadways and yard areas should have a pave, suitable for wheeled traffic. Dust development shall be prevented. • Adequate drainage and sewage disposal systems shall function at all times. Drains must be covered adequately • Waste collection and storage areas must be paved, cleaneble and equipped with drains

  6. Plant site and location • Establishments should normally be located away from: • environmentally polluted areas and industrial activities which pose a serious threat of contaminating food • areas subject to flooding unless sufficient safeguards are provided • areas prone to infestations of pests • areas where wastes, either solid or liquid, cannot be removed effectively

  7. Design and layout: • The internal design and layout of food establishments should permit good foodhygiene practices, including protection against cross-contamination between and during operations by foodstuffs • Layout must be in a logical sense, straight line, but U is acceptable • areas with conflicting functional purpose which could potenctially affect product must be clearly segregated though partition, location or other effective means (ZONING)

  8. Condition of floor • Floors should be designed to withstand the rigours of the production processes that are being conducted • Floors must be made of impervious, non toxic materials, washabel, non absorbent, and be free from cracks and open joints • The floor surface must be impervious to moisture and grease, resistant to chemicals and food materials to which it may be exposed and safe to walk on when wet, dry or greasy. • Floor must be kept clean and free from the accumulation of water or other spillage’s, specially in corners and areas hidden by equipments, material, etc.

  9. Condition of floor • Sufficient sloping of floors to drains and trapped outlets exist where appropriate. • Coved wall and floor junctions should facilitate cleaning. • Demaged flooring must be reparaired as quicly as possible with materials compatible with the original flooring and in a permanent fashion.

  10. Condition of walls, doors and windows • WALLS • All interior walls in rooms where open food is stored or processed must be in good condition and finished with a hygienic, easy to clean surface, which does not pose a foreign hazard e.g. Walls should be finished with a continous, bonded surface and protected from damage. Corners, joints between cladding sheets or ceramic tiles must be sealed with a suitable impervios sealant. • Walls and wall surface should be free from shelves and other protruding attachments wherever possible. The design must me such as to avoid any horizontal surface, which could act as a dust trap, or impromptu shelf space,

  11. Condition of walls, doors and windows • WALLS • All wall-wall and wall-floor junctions should be coved. Wall ceiling junctions and other juctions should be coved or sealed to facilitate cleaning • Walls are be white or light coulored • All signs of deterioration and damage should be dealt with immediately and the repairs should be compatible with the original finish. • Services must be sealed into any wall through they pass (electrical fittings, plumbing..)

  12. Condition of walls, doors and windows • DOORS • All external opening doors must be kept closed. Where frequent use makes this impractical then either automatic doors, rubber swing doors, plastic strip curtaining or air curtain should be provide to prevent bird and insect ingress • All doors to production areas should be self-closing to mantain the necessary atmospheric conditions. They should be close fitting on all sides and the doorframes and corners must be given protection against damage.

  13. Condition of walls, doors and windows • WINDOWS • All windows should be kept closed. Those required to be opened to provide additional ventilation, should have the total opening area screened with a mesh small enough to exclude flying insects. These insect-proof screens can be easily removed for cleaning • All exterior windows must be clear, complete and properly fixed. Their frames must be of sound fitting and completely sealed to prevent insect ingress

  14. Condition of walls, doors and windows • WINDOWS • Broken or cracked windows must be replaced imediately before production recommences. Approved shatterproof materials must used. • Windowsills and ledges should be sloping to prevent tools and other articles being placed on them

  15. Condition of ceiling and lights • CEILING • In any room where open food is stored or processed, the condition of the ceiling must be smooth, easily cleaned and kept in good repair. It must not pose a foreign body hazard to the area below, The finishing material must be selected to prevent the shedding of particles (i.e. Paint flakes, rusty particles, etc.) and mould development. • Ceilings may be underdrawn or suspended, however, access must be provided to the void above to enable adequate cleaning and pest control inspections. Adequate walkways must be provided for this purpose and also for access to services

  16. Condition of ceiling and lights • CEILING • All junctions between walls and ceilings should be sealed and impermeable to facilitate cleaning. Additionaly eves and ridges must be sealed to prevent access to birds, insects, and rodents. • Where painted suface are unavoidable, both these and underlying surfaces must be sound and free from flaking, and repainted as necessary with a paint approved for use in food preparation areas.

  17. Condition of ceiling and lights • LIGHTS • Light bulbs/fluorescent tubes and fixtures, including elecrical UV-light insect control units suspended in food handling areas in any stage of production, must be of safety type and protected to prevent contamination of food in case of breakage. • All light units must be kept clean, and bulb replacement or any other maintenance carried out when the department is not in production.

  18. Condition of drainage • The capacitiy of the drains must be sufficiente to cope wih the maximum process requirementes placed on them. • Drains must be non-corrodable, trapped, easy to clean and durable • The flow of drains shall be from high to low risk to avoid contamination of the clean environment.(1% slope) • The drains and gullies covered with removable easily grids are recommended

  19. Other elements • Any stairsways to or from mezzanine floors or gangways over production lines must be sealed and include side walls to prevent product contamination • Shelves and racks in storage areas must be of hygienic contruction and of non corrodable material • Pipelines, fixtures, light fittings, cable chanels, ventilation points and other everhead structures and services in manufacturing areas, must be installed such that sagging and any connections, surface, joints, etc.. Which are difficult to clean and inspect , are avoided, • Pipelines should be clearly identified to show direction and contents

  20. Sanitary facilities • They should be hygienic in design, easy to clean, prevent the acumulation of dirt and dust, kept in clean and hygienic condition and well maintained. • Appropriate and adequate facilites for hand washing and drying shall be provided in sufficient number and conveniently located in processing area • The hand-washing facilities must include hot and cold water, preferably from mixing taps of a non han operable type. Liquid soap and, where appropiate, facilities for hand disinfection should be provided

  21. Sanitary facilities • Disposable paper or re-washable, one-use roller dispensed textile towels shall be used for hand drying. • Air-dryers are not recommended • Where paper towels are used, a sufficient number of dispensers and appropriate waste receptacles shall be provided adjacent to each washing facility • Toilets shall be provided in a sufficient number in all establishments. • They shall be easily accessible and not open directly into food handling areas.

  22. Sanitary facilities • Toilets shall be well lit and ventilated and easy to clean and sanitise • Cloakrooms shall be well lit, ventilated and provide enough space for users • Sufficient and adequate lockers (one per person) should be provide as well as adequate storage facilities for shoes and boots • Lockers should facilitate clear segregation between working and civilian clothing

  23. Sanitary facilities • A lockable room or facility to store cleaning and disinfection agents shall be provide as well as a segregated facility to dry an store cleaning tools.

  24. Equipment and utensils • Equipment and utensils must be designed, contructed and installed or used to suit the specified purpose, to prevent any product contamination, to allow for esasy inspection, to prevent pest breddin and to enable easy dismanting, cleaning and disinfection. • Wood and glass should be avoided, unless such use can be justified • Equipment and utensils must be dedicated clearly for food or non food use and be identified and use accordingly.

  25. Equipment and utensils • Utensils or tools, used in food production or coming into contact with food or food processing equipment shall be clearly differentiated in colour from any other tools and utensils (cleaning tools) • All utensils must be stored adequately • Equipment should be located so that it: permits adequate maintenance and cleaning; functions in accodance with its inteded use; and facilitates good hygiene practices, including monitoring. • Equipment must be positioned at least 50 cm Away from the wall and off the floor

  26. Equipment and utensils • Equipment design • Must be designed for the tpe of product (haccp) • Must allow for sampling and monitoring (where required) • Position of motors and pumps (not over product) • Must easy clean (CIP or easy to take apart for manual cleaning) • Must be easy to mantain • Must have product contact surfaces compatible with product • Corners must be rounded • exterior surface must be easy to clean

  27. ZOONING

  28. ZONING A CRITICAL ELEMENT OF ALL PREVENTION PLANS

  29. Zoning is an integral part of manufacturing plans, control procedures and GMP. • Is a part of a factory´s total plan for prevention, never to be considered in isolation, must to be supported by many other preventive measures such correct cleaning and good equipment installation. • Zoning is successful only if all personnel and visitors to the factory understand them.

  30. ZONING AND LAYOUT FOR PREVENTION Keeping out and keeping away unwanted items, animals and people from the product contact points is a major step towards prevention of food hygiene problems.

  31. ZONING FOR PREVENTION What is zoning ? • Zoning suggests divisions and limitation (barriers) • Zoning is equivalent to dividing into areas, each having a well-defined use • Zoning is part of a total concept to prevent product contamination • Zoning implies a knowledge of product, process and preventive measures ..but most important zoning will be ineffective without coaching and correct attitudes.

  32. ZONING FOR PREVENTION Zoning is closely related to: Needs for Product safety and Safety of the consumer But zoning must remain realistic an affordable Within the local limits and those of manufacturing

  33. ZONING FOR PREVENTION Zoning a new factory is relatively easy But zoning an existing factory can be a very costly and time consuming exercise ...Compromises or justification of investments may be essential as long as food safety is never put at risk

  34. ZONING FOR PREVENTION How to proceed sensibly and systematically. • Form a multidisciplinary team • Establish required level of product protection; use HACCP and other information • Discuss with all concerned • In existing factories, study all circulations • For projects make preliminary circulation plan • Establish all details of hygienic design for barriers and installations • Plan associated routines and organise training

  35. BRAINSTORMING for APPROPRIATE ZONING. • What is the product/consumer concern? • Is this related to food safety? • Are there local concerns related to this issue? • What are the product specifications? • What are the sampling plans and inducators? • What are the contamination sources of concerns? • What is the microbiological history of the facility? • What cleaning procedures are used for equipment? • What cleaning procedures are used for the environment? • What services are necessary? • What are the incoming goods?

More Related