1 / 35

Field Period Assembly

Field Period Assembly. Slides for discussion Rev 3. (VV Prep). Stage 1. (Half Period Assembly). Lower segment, shim and fasten. Stage 2. (MC installation). Stage 3. (Final FP Assembly). Stage 4. VV Prep Stage. Earlier installation orientation. Lower segment, shim and fasten.

yardan
Download Presentation

Field Period Assembly

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Field Period Assembly Slides for discussion Rev 3

  2. (VV Prep) Stage 1 (Half Period Assembly) Lower segment, shim and fasten Stage 2 (MC installation) Stage 3 (Final FP Assembly) Stage 4

  3. VV Prep Stage Earlier installation orientation

  4. Lower segment, shim and fasten MC segment alignment system Half Field Period Assembly

  5. Module Coil Installation

  6. Final Field Period Assembly Figure 7a Initial TF Placement Figure 7b) Initial TF Placement Figure 7 Final Full Period Assembly

  7. 34.8’ 21.25’

  8. Stage 3 Stage 1 TF FP Stage 4 Stage 2

  9. It is assumed that there is some form of pre-assembly of the TF coils

  10. Se185-009.asm 23,000 lbs Se185-006.asm 3,203 lbs Se185-005-01.asm 6,000 lbs Se185-008.asm 4,012 lbs 18,700 Se185-007.asm 2,660 lbs Se185-004.asm 2,825 lbs Total 41,700 lbs

  11. MCAF Component Details Module Coil Half Period (25000 lbs) MCHP / Turning Fixture interface Pivot and rotation component (3200 lbs) Cradle component (6000 lbs) Vertical guide component (4000 lbs) 18,700 lbs (2700 lbs) Linear turntable structure Linear motion structure (2800 lbs)

  12. RY = 13° RX = 5° DZ = 16” RZ = 15° DX = 12” Z Y X DY = 140” Total Weight of Reference Turning Fixture is ~18,700 lbs (assumes steel construction) • Design uses: • structural steel components • worm gear screw assemblies • rollers

  13. Vacuum Vessel Period Module Coil Half Period Module Coil Half Period

  14. Sideways clearances between MC shell and secondary support structure shall be greater that 60”

  15. Gantry Crane Module Coil Half Period Turning Fixture / MC Interface Components Module Coil Half Period Type “C” Turning Fixture Type “A” Base Guide Rail VV Support Type “B”

  16. Gantry Crane Module Coil Half Period Module Coil Half Period Turning Fixture Base Guide Rail

  17. Y Y X Z Rz X Rx X Ry . X Z

  18. Length of screw shown is 172” If we allow a rotational extraction of the MCHP it looks like we can come under the 144” max length of the screw. A 144” screw would reduce the 63’ space savings by 28”, leaving 35” of space. 63” potential space savings.

  19. Max stress = 11 ksi Max Disp = .09 in Load = 23,000 lbs Total Unit weight = 36,410 lbs

  20. Starting Position - CG Locations (Base End and Front Views) 18,300 MCFP 38,000 MCAF

  21. 89.1” Starting Position - CG Locations (End and Top Views from Vertical Guide Structure) 18,300 MCHP 38,000 MCAF

  22. Final Position - CG Locations (Front and Top Views from Base Structure) 18,300 MCHP 38,000 MCAF 100.0”

  23. 0.54” 74” 82” 1 1 3 2 2 3

  24. Machine Coordinate System Y Z 60 Deg X Baseline MCAF Coordinate System 66.753”

  25. C5 B5 A5 C4 A6 B4 B6 A4 C6 A3 C1 B3 B1 C3 A1 C2 B2 A2 Half Period Assembly Sequence – perform all alignment and hole placement at this stage.

More Related