1 / 20

Powering tests with the PP2 regulator

Powering tests with the PP2 regulator. Laura Gonella Physikalisches Institut Uni Bonn. Power configuration with regulators. Rext = 10kOhm. PP2 regulators´ setup. 1.8V. Type2 cables. Rext = 18kOhm. Vreg. Vsense. Vin1 Vin2. VDDA VDDD. I1 I2. Measured at the pad.

Download Presentation

Powering tests with the PP2 regulator

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Powering tests with the PP2 regulator Laura Gonella Physikalisches Institut Uni Bonn

  2. Power configuration with regulators Rext = 10kOhm PP2 regulators´ setup 1.8V Type2 cables Rext = 18kOhm Vreg Vsense Vin1 Vin2 VDDA VDDD I1 I2 Measured at the pad Measured across R=10mΩ L. Gonella

  3. Rext2 = 18KOhm L. Gonella

  4. Transients • All inputs and outputs of the regulators are very noisy if looked at with a single ended probe • Most likely a ground problem cause the situation is much better when using a differential probe, except for one input • The input of Reg1 observed with a differential probe shows a disturbance of 250MHz freq and ~400mV amplitude which appears as soon as the clock is switched on Clock on Clock off L. Gonella

  5. Transients • Reducing the bandwidth to 20Mhz it is possible to see the levels shifting • No transients are observed but this could be due to the chosen bandwidth • Single ended probes (passive (blue), active (pink)) I = 0.510A -> 0.290A I = 0.290A -> 0.510A Reg1 input Reg1 input VDDA VDDA L. Gonella

  6. Power configuration 1 PP2 regulators´ setup Type2 cables Vreg0 Vreg1 Vsense1 VDDA VDDD Measured at the pad L. Gonella

  7. Voltages and currents • I is the current measured at the supply for the PP2 regulator board. It includes analog and digital current for the chip, plus 10mA biasing current of the PP2 regulators • Analog and digital currents (resp. Ia and Id) are calculated considering R = 1.9Ω for the type 2 cables L. Gonella

  8. Threshold L. Gonella

  9. Threshold – PrmpVbp*2 L. Gonella

  10. Power configuration 2 • Short between VDDD and VDDA is done on the board Type2 cables PP2 regulators´ setup Vreg1 Vsense1 VDDA VDDD Measured at the pad L. Gonella

  11. Voltages and currents L. Gonella

  12. Threshold L. Gonella

  13. Threshold – PrmpVbp*2 L. Gonella

  14. Summary of threshold and noise L. Gonella

  15. Backup L. Gonella

  16. Power configuration with regulators PP2 regulators´ setup 1.8V Type2 cables Vreg Vsense Vin1 Vin2 VDDA VDDD I1 I2 Measured at the pad Measured across R=10mΩ L. Gonella

  17. Voltages and currents L. Gonella

  18. Threshold scan L. Gonella

  19. Threshold scan – PrmbVbp*2 L. Gonella

  20. PP2 regulator vs commercial supply • Comparison of threshold and noise values for this powering configuration with power from the PP2 regulators and with a commercial supply (shown 2 weeks ago) L. Gonella

More Related