EE365 Adv. Digital Circuit Design Clarkson University Lecture #6

1. EE365 Adv. Digital Circuit Design Clarkson University Lecture #6 Timing and Related Design Considerations

2. Topics • Signal Naming Conventions -Buses • Timing Diagrams • Data Book Reference • Timing Specifications • Timing Hazards Lect #6 Rissacher EE365

3. Buses • A group of digital signals which carry multi-bit data • Shown on a block diagram with a single (or double) line • Shown on a logic diagram (schematic) with a single (sometimes heavier) line • Usually named using an indexed notation: ADDR0, ADDR1, ADDR2, … or ADDR[7:0] or ADDR (7 downto 0) Lect #6 Rissacher EE365

4. Timing Diagrams • Graphical representation of circuit behavior over time • May be used as a device specification • illustrates device performance • May be used as a module or system specification • identifies a requirement for system performance • May be used as a tool in system analysis Lect #6 Rissacher EE365

5. Example Timing Diagram • Functional Timing Diagram • assumes zero delays • simply demonstrates logic relations Lect #6 Rissacher EE365

6. Example Timing Diagram • Functional diagram is useful for showing causal relationships • This is often done with a curved arrow leading from an input transition to the resultant output transition • Notice that transitions are shown as vertical lines, but in reality these always require a non-zero time for making a transition Lect #6 Rissacher EE365

7. Example Timing Diagram • Timing Diagram (more realistic) • shows delays using typical or maximum values Lect #6 Rissacher EE365

8. Propagation Delay • The delay between an input transition and the resultant output transition is called propagation delay • Propagation delay is measured between the centers of the transition time period Lect #6 Rissacher EE365

9. Propagation Delay • Propagation delay for an output transition from high to low is tpHL • Propagation delay for an output transition from low to high is tpLH • Notice that these two times are not necessarily the same for the same device • Notice the difference from Transition Times Lect #6 Rissacher EE365

10. Recall: Transition times Lect #6 Rissacher EE365

11. Data Book Reference Lect #6 Rissacher EE365

12. Timing Specifications Shows uncertainty in propagation delay Lect #6 Rissacher EE365

13. Timing Specifications Shows uncertainty in signal value used to show timing when signal value is not relevant used to show timing for bus signals Lect #6 Rissacher EE365

14. I/O Rate Considerations The inputs to the system can come at a certain rate if the expected logic function is to be accurately represented by the output Propagation Delays need to be considered Lect #6 Rissacher EE365

15. Timing Hazard Transient output behavior may not agree with predicted output due to delay differences A glitch is the presence of extra signal transitions which are not predicted from the logic equations Lect #6 Rissacher EE365

16. Static Hazards A static hazard is the possibility of a glitch when the output should not change A static-1 hazard is present if changing a single input variable may produce output transitions but the output logic function is high (1) independent of this change. Lect #6 Rissacher EE365

17. Example of a Static-1 Hazard Lect #6 Rissacher EE365

18. Detection of Static-1 Hazards A properly designed OR-AND circuit will never have static-1 hazards An AND-OR circuit may have static-1 hazards These can be detected from a K-map Check for adjacent minterms NOT covered by the same product term (AND gate) in the actual realization Lect #6 Rissacher EE365

19. Detection of a Static-1 Hazard X = 0 X = 1 The static-1 hazard can be detected by noticing that there are two adjacent minterms (3) and (19) which are not covered by a common product term. It can be eliminated by including an additional product term in the realization. Lect #6 Rissacher EE365

20. Hazard Free Circuit Lect #6 Rissacher EE365

21. Static Hazards A static-0 hazard is present if changing a single input variable may produce output transitions but the output logic function is low (0) independent of this change. While hazards produce unexpected transitions and may be intermittent, proper design of synchronous sequential circuits should tolerate hazards. Lect #6 Rissacher EE365

22. Detection of Static-0 Hazards A properly designed AND-OR circuit will never have static-0 hazards An OR-AND circuit may have static-0 hazards Check K-map for adjacent maxterms NOT covered by the same sum term (OR gate) in the actual realization Lect #6 Rissacher EE365

23. In-Class Practice Problem Correct any static-1 hazards in the following function (circle on map and write new F function) Lect #6 Rissacher EE365

24. In-Class Practice Problem Lect #6 Rissacher EE365

25. Dynamic Hazards A dynamic hazard is the possibility of a glitch when the output changes from low to high or high to low Since the output is supposed to change, the presence of a glitch means the output makes more than one transition low  high  low  high high  low  high  low Lect #6 Rissacher EE365

26. Dynamic Hazards Do not occur in properly designed two-level circuits What is “properly” designed ? no first level gate has both true and complement forms of the same signal as inputs Lect #6 Rissacher EE365

27. Hazards in Other Circuits NAND-NAND circuits - equivalent to AND-OR NOR-NOR circuits - equivalent to OR-AND Multi-level circuits have more than two levels of logic (not counting inverters) may have static and/or dynamic hazards Lect #6 Rissacher EE365

28. Next Class Intro to MSI PLDs Decoders Lect #6 Rissacher EE365